Fuji Electric FRENIC-Eco FRN-F1 Serie Guía Rápida página 22

J codes: Application functions
Code
J01
PID control
Mode selection
J02 Remote process command
J03 P (gain)
J04 I (integration time)
J05 D (differential time)
J06 Feedback filter
J10 Anti reset windup
J11 Select alarm output
J12 Upper limit alarm (AH)
J13 Lower limit alarm (AL)
J15 Stop frequency for slow flowrate
J16 Slow flowrate level stop latency
J17 Starting frequency
J18 Upper limit of PID process output
J19 Lower limit of PID process output
J21 Dew condensation prevention (Duty)
J22 Commercial power switching sequence
J25 Pump control
J26 Motor 1 mode
J27 Motor 2 mode
J28 Motor 3 mode
J29 Motor 4 mode
J30 Motor switching order
J31 Motor stop mode
J32 Periodic switching time for motor drive
J33 Periodic switching signaling period
J34 Sequenced start of commerc ial power-
driven motor
J35
J36 Sequenced stop of commercial power -
driven motor
J37
J38 Contactor delay time
J39 Switching time for motor sequenced start (Deceleration time)
J40 Switching time for motor sequenced stop (Acceleration time)
J41 Motor sequenced start/sequenced stop switching level
J42 Switching motor sequenced start/sequenced stop (Dead band)
J43 PID control startup frequency
Name
0: Disable
1: Enable (normal operation)
2: Enable (inverse operation)
0: Enable arrow keys on keypad
1: PID process command 1
3: Enable terminal command UP/DOWN control
4: Command via communications link
0.000 to 30.000 times
0.0 to 3600.0 seconds
0.00 to 600.0 seconds
0.0 to 900.0 seconds
0 to 200 %
(Refer to FRENIC -Eco user's manual)
0 to 100 %
0 to 100 %
0: Disable
1 to 120 Hz
1 to 60 seconds
0: Disable
1 to 120 Hz
1 to 120 Hz
999: Depends on setting of F15
1 to 120 Hz
999: Depends on setting of F16
1 to 50 %
0: Keep inverter operation (Stop due to alarm)
1: Automatically switch to commercial-power operation
Mode selection 0: Disable
1: Enable (Fixed, inverter driven)
2: Enable (Floating, inverter driven)
0: Disable (Always OFF)
1: Enable
2: Force to run by commercial power
0: Fixed
1: Automatically (Constant run time)
0: Stop all motors (inverter-driven and commercial power -driven)
1: Stop inverter-driven motor only (excl. alarm state)
2: Stop inverter-driven motor only (incl. alarm state)
0.0: Disable switching
0.1 to 720.0: Switching time range
999: Fix to 3 minutes
0.1 to 600.0 seconds
Frequency 0 to 120 Hz
999: Depends on setting of J18
(This code is used to judge whether or not to stop a commercial power -
driven motor by checking the output frequency of the inverter-driven
motor)
Duration 0.00 to 3600 seconds
Frequency 0 to 120 Hz
999: Depends on setting of J19
(This code is used to judge whether or not to stop a commercial power -
driven motor by checking the output frequency of the inverter-driven
motor)
Duration 0.00 to 3600 seconds
0.01 to 2.00 seconds
0.00: Depends on the setting of F08, 0.01 to 3600
0.01 to 3600 seconds
0.00: Depends on the setting of F07, 0.01 to 3600
0.01 to 3600 seconds
0 to 100 %
0.0: Disable
0.1 to 50.0 %
0: Disable
1 to 120Hz
999: Depends on the setting of J36
Chapter 6: Function codes and application example
Data setting range Default setting
0
0
0.100 times
0.0 seconds
0.00 seconds
0.5 seconds
200 %
0
100 %
0 %
0
30 seconds
0
999
999
1 %
0
0
0
0
0
0
0
0
0.0 seconds
0.1 seconds
999
0.00 seconds
999
0.00 seconds
0.00 seconds
0.00 seconds
0.00 seconds
0 %
0.0 %
999
19