Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Do not load the machine over its specified capacity
(see Mixing Capacity).
9.1 Dust emission reduction system
The mixer is equipped with a ring located on the drum, which
can be connected via the fitting (ref.13, fig. 1) to a dust
extraction system (not supplied with the machine) to reduce
the amount of dust emitted.
10. STOPPING THE MACHINE
- To stop the machine, press the button on the electrical panel
(ref.12, fig.1).
11. MAINTENANCE
- Maintenance operations must be performed by suitably
trained, experienced personnel.
- Worn or faulty parts must be replaced with original
replacement parts.
- It is advisable to remove any dirt and deposits formed in the
drum during mixing by washing with plenty of water.
Every two months of operation, check:
• the belt tension.
• the condition of the poly-V drive belt and pulleys.
Check weekly that the plug contacts on the electrical cabinet
are clean, dry and rust free.
- Periodically check the condition of the sheaths of the power
cables exiting the electrical panel.
- Periodically check that the machine stops rotating when the
drum safety guard is raised by 10 mm.
11.1 LIMIT SWITCH ADJUSTMENT
Adjustment of the limit switch must be carried out with the
drum safety guard in the lowered position. Loosen the cam
retaining screws, position the cam so that the track is in
correspondence with the limit switch roller, and then fully re-
tighten the screws.
11.2 CLEANING THE OUTLET GUARD
Undo the screws and remove the guard. To refit, align the
holes in the guard with the fixing holes, fit the screws and
tighten them.
Before starting the mixer, check that the outlet guard
is fitted correctly.
11.3 BELT TENSIONING (fig.6)
1. Switch off the motor and unplug the mixer from the power
supply.
2. Loosen the 4 screws securing the mounting of the electric
motor and tension the belt by turning the tensioner screw.
- Do not overtension the belt, as this increases the rate of
wear on the belt itself and on the bearings of the motor
and gearbox.
3. After tensioning the belt, re-tighten the 4 screws.
11.4 BELT REPLACEMENT (fig.6)
1. Switch off the motor and unplug the mixer from the power
supply.
2. Remove the belt guard by removing the retaining screws.
3. Loosen the 4 screws securing the mounting of the electric
motor and fully unscrew the tensioner screw.
4. Allow the motor to drop on its mounting and remove the belt.
5. Fit the new belt to the pulley of the gearbox.
6. Return the motor to its original position, ensuring that the
belt is correctly seated on the drive pulley.
7. Tension the belt by turning the tensioner screw.
8. After tensioning the belt, re-tighten the 4 screws.
IMER INTERNATIONAL S.p.A
9. Refit the belt guard with its retaining screws.
Check the belt tension again after the first 4 hours of
operation, and repeat the check every 18-20 hours.
fitted correctly.
12. TROUBLESHOOTING
performed exclusively with the machine switched off and
unplugged from the power supply socket.
PROBLEMS
The motor does
not start when the
start
pressed.
Discharge
does not open
13.RESIDUAL RISKS AND SAFETY NOTICES
Although the saw has been manufactured in full compliance
with current regulations, residual risks exist that cannot be
eliminated and which require the use of appropriate personal
protection equipment. The machine is equipped with notices to
indicate the residual risks and how to avoid them.
NOISE HAZARD
HAND CRUSHING/SHEARING HAZARD
EYE INJURY HAZARD
11
Before starting the mixer, check that the belt guard is
CAUTION! All maintenance operations must be
CAUSES
-
No
electrical
power.
switch
is
- Plug and power
supply socket not
properly connected.
- The power cable
from the plug to
electrical panel is
broken.
- An electrical wire
in
the
electrical
panel
disconnected.
- An electrical wire
in
the
motor
terminal
board
disconnected.
- A fuse in the
electrical panel has
blown.
- drum safety guard
open.
-
Limit
switch
malfunction
- The cam is not
installed correctly
outlet
-
Outlet
guard
obstructed
Wear ear defenders
Wear gloves
Wear safety glasses
REMEDIES
Check the line
- Restore
correct
connection.
- Replace cable
- Reconnect
is
- As above
is
- Replace the fuse
- Close
- Replace
-
Refer
to
the
instructions
for
adjustment of the
limit switch "11.1"
- Remove and clean
outlet guard (See
Cleaning the outlet
guard "11.2")
Tabla de contenido
