Flex Valve Disassembly/Assembly - Tippmann X7 PHENOM Manual Del Usuario

E
1. To remove the
N
reinstall it, just turn it clockwise to thread it into the Upper Receiver.
G
2. To remove the
L
pins (12 and 13), from the assembly. Notice that #12 is longer than #13; keep them
I
separated. The Front Grip/Shroud Assembly can now be removed. To remove the
S
Front Sight
end of the barrel until it comes off.
H
3. To remove the
the magazine release button (see arrow in Figure
11), then pull the magazine down to remove. Be sure
to keep the opposite side of the receiver clear while
pressing the button to allow the magazine to release.
The Magazine is designed to hinge open to allow for
storage of tools and grease.
4. To remove the
(12), from the Lower Receiver assembly. Pull the Lower
Receiver straight down to get it apart from the Upper
Receiver assembly.
5. Remove remaining parts from the
a. Remove the last remaining
b. Pull the
End Cap
c. Pull the
Pressure Gauge Plug
d. Slide the Cyclone Feed System
Hose Fitting from the Valve assembly.
e. The
Valve
Spring
lubricate the specified parts with Tippmann grease every 8-10,000 shots and prior to
re-assembly.
6. To remove the
turning clockwise and lifting from the CFS. Remove the
have been disconnected in the previous step. Set the CFS aside; see page 24 for
further disassembly of the CFS.
7. To remove the
Receiver rail.

Flex Valve Disassembly/Assembly

It is not necessary to disassemble the Upper Receiver to access and service the Flex Valve
assembly or its internal parts. The Valve can be slid out the back of the receiver as described
in Step 5.e. above.
Disassembly instructions (refer to Figures 13 and 14 on page 19):
1. Inspect and clean the exterior of the
2. Remove the
Replace if damaged.
3. Using a 3/16" or 1/8" Allen wrench, remove the
counterclockwise until it is loose. Set aside.
4. Pull the
Spring
workbench, and the
the Regulator Piston with Tippmann grease every 8-10,000 shots and prior to re-
assembly. There is no need to further disassemble the marker for normal maintenance.
5. Hold the Valve Body with your hand while using an adjustable wrench to turn
(counterclockwise) the
(16), simply unscrew the Barrel from the Upper Receiver, and to
Barrel
Front Grip/Shroud Assembly
(18), remove the
Bolt
(17) from the receiver, press
Magazine
Lower Receiver
Push Pin
(11) from the rear of the Upper Receiver.
assembly (47),
Front Bolt
(6) all slide out from the open end of the Upper Receiver. Inspect, clean, and
Cyclone Feed System
(20), remove the
Rear Sight
(49) and the
Bumper Disk
(64) out the back. Lightly tap the rear of the Valve Body on the
Regulator Piston
Regulator Body
(15), pull each of the two push
(19) and slide the Front Sight towards the muzzle
, pull two push pins
:
Upper Receiver
(13) from the Upper Receiver.
(9) from the Upper Receiver.
(3) back to the keyhole and pull the
Hose Fitting
assembly (7), and the
(CFS), first remove the
(19) and slide off from the Upper
Bolt
assembly (47).
Valve
Spacer Washer
Velocity Adjuster
(63) comes out. Inspect, clean, and lubricate
(61) out from the Valve Body. Once removed,
16
Figure 11: Magazine Release
Button
Compression
(22) by
Hopper
(14). The
Bolt Hose
(48). Clean and inspect.
(65) by rotating it
(4) should