Tabla de contenido
DK
AKKU-BOREMASKINE
Tak, fordi du har valgt dette Ferm produkt.
Du har nu et fremragende produkt, som er
fremstillet af en af Europas førende
leverandører.
Alle produkter fra Ferm er produceret i
overensstemmelse med de
højeste standarder for ydeevne og sikkerhed.
Som en del af vores filosofi yder vi også en
fremragende kundeservice, som understøttes af
vores omfattende garanti.
Vi håber, at du vil nyde at anvende dette produkt
i mange år.
Numrene i den nedenstående tekst henviser
til illustrationerne på side 2 - 4.
Læs denne brugsanvisning nøje
igennem, før maskinen tages i brug. Gør
dig fortrolig med funktionerne og
betjeningen. Maskinen skal
vedligeholdes i overensstemmelse med
anvisninger, så maskinen altid fungerer
problemfrit. Brugsanvisningen og
dertilhørende dokumentation skal
opbevares i nærheden af maskinen.
Indhold
1. Maskindata
2. Sikkerhedsinstruktioner
3. Montering af tilbehør
4. Betjening
5. Service & vedligeholdelse
50
All manuals and user guides at all-guides.com
1. MASKINDATA
Tekniske specifikationer
Spænding
14,4 V
Spænding, batterioplader
230 V~
Frekvens, batterioplader
50 Hz
Batteriefekt
1,1 Ah
Opladningstid
3-4 timer
Antal borehastigheder
2
Maks. drejningsmoment
(lav hastighed)
12 Nm
Omdrejningstal, ubelastet
Position I
0-400/min
Position II
0-1150/min
Borepatronens kapacitet
0,8-10 mm
Vægt (inkl. batteri)
2,0 kg
Lydtryk
80,0 dB(A)
Lydeffekt
91,0 dB(A)
Vibrationsværdi
1,4 m/s
2
Pakningens indhold
1 ledningsfri boremaskine
1 batteri
1 oplader
2 dobbelte bits
1 betjeningsvejledning
1 sikkerhedsvejledning
1 garantikort
Efterse apparatet, eventuelle løsdele og
tilbehøret for transportskader.
Produktoplysninger
Fig. A
1.
Retningskontakt
2.
Batteriudløsningsknap
3.
Batteri
4.
Tænd/sluk-kontakt
5.
Ring til indstilling af drejningsmoment
6.
Spændepatron
7.
Hastighedsvælger
2. SIKKERHEDSINSTRUKTIONER
Symbolforklaring
Betegnelse for risiko for personskader,
dødsfald eller beskadigelse af værktøjet
i tilfælde af at du er uopmærksom på
instruktioner i denne manual.
Ferm
•
Loosen the drill chuck (6) by rotating the hand-
grip (8).
•
Insert the shaft of the drill cutter into the chuck.
•
Tighten the drill chuck so that the drill cutter is
firmly clamped.
•
Rotate the drill chuck in the opposite direction
when you wish to change the cutter.
Connecting and removing the battery
Fig. C
Ensure that the exterior of the battery
block or tool is clean and dry before
connecting the charger.
•
Ensure that the direction reversing switch
(1, Fig. A) is in the central position in order to
prevent the appliance from being switched on
unexpectedly.
•
Insert the battery (3) into the base of the
appliance, as shown on the illustration. Push
the battery until it latches in.
•
Press the locking buttons (2) on both sides
before removing the battery, and disengage
the battery from the base of the appliance.
OPERATION
4. OPERATION
Always follow the safety notes and the
relevant safety code.
Hold the appliance firmly and press the drill
steadily onto the workpiece. Do not overload
the appliance. Only use drills with no visible
wear. Worn drills will have a bad effect on the
functioning of the appliance.
Adjusting the speed
Fig. D
The appliance has two drill speeds.
•
For slow drilling or for driving or removing
screws, set the speed selection switch (7) to '1'.
•
For fast drilling set the speed selection switch
(7) to '2'.
Never switch over when the motor is
running!
Ferm
Adjusting the torque
Fig. E
The appliance has 16 different torque settings
with which to set the power for driving and
removing screws.
•
Set the torque adjustment ring (5) to the
desired position. The available torque settings
are indicated on the adjustment ring by the
numbers 1 to 8 and by dots between the
figures to define intermediate settings (16 in
total).
•
You should preferably choose a setting as
low as possible when using the screwdriver.
Select a higher setting if the motor slips.
Driving and removing screws
Fig. A
•
Set the direction reversing switch (1) to
position ' ' in order to drive screws.
•
Set the direction reversing switch (1) to
position ' ' in order to remove screws.
Drilling
•
Rotate the torque adjustment ring (5) to the
drilling position.
Ensure that the direction reversing
switch (1) is always set to ' ' during
drilling.
Switching the device on and off
Fig. A
•
Depress the on/off switch (4). It regulates the
speed of the appliance by transmitting power
to the switch.
•
Release the on/off switch (4) to halt the drill
chuck immediately, it will no longer run on.
•
Move the direction reversing switch (1) to the
centre in order to lock the appliance in its
disabled state.
Only lay down the appliance when it has stopped
running completely. Do not place it on a dusty
surface as particles of dust could get into the
mechanism.
Charging the battery
•
The included battery is delivered in partly
charged condition.
•
Only use the battery charger in a temperature
range between + 5 °C to + 40 ºC.
•
Only use the battery charger in dry, ventilated
rooms.
GB
7
Tabla de contenido
