Harman Kardon AVR 1700 Guia De Inicio Rapido página 8

AVR
5. Use the remote's arrow and OK buttons to select "EzSet/EQ."
E z S e t / E Q
P l a c e m i c r o p h o n e a t l i s t e n i n g
p o s i t i o n a n d p l u g i n t o H e a d p h o n e
J a c k .
D o y o u w a n t t o s t a r t E z S e t / E Q ?
Y e s
N o
6. Select "Yes." The Speaker Configuration menu wlll appear.
E z S e t / E Q
S p e a k e r c o n f i g u r a t i o n .
5 . 1
C a n c e l
7. Select "5.1."
8. Remain silent while the test noise plays through your system's speakers. When the
calibration has completed, press the OSD button to exit.
Assign the AVR Input Connections
1. Review the input connections you listed on the connection table, on page 4. Note what
changes (if any) you have made from the default AVR Input Connector assignments
that appear on the list. If you connected your source devices according to the entries
in the "Default AVR Input Connector" column of the table on page 4, you can skip this
section.
2. Turn on your TV and select the TV input where you connected the AVR in Connect Your
TV, on page 3.
3. Press the remote control's OSD button. The AVR's on-screen display (OSD) setup menu
will appear on the TV. (Note: If you have used a composite video connection to your
TV, the OSD menus will not appear on your TV. Follow the steps below using the AVR's
front-panel display.)
M A S T E R M E N U
S o u r c e S e l e c t
S o u r c e S e t u p
S u r r o u n d M o d e
E z S e t / E Q
M a n u a l S e t u p
N e t w o r k
S y s t e m S e t u p
8
All manuals and user guides at all-guides.com
4. Use the remote's arrow and OK buttons to select "Source Setup." If there is a Source Selector
for which you want to assign different video or audio connections. use the left/right arrow
buttons to select it, and press the OK button.
S o u r c e S e t u p
S o u r c e
T i t l e
V i d e o I n
A u d i o I n
T o n e
B a s s
T r e b l e
N i g h t M o d e
R e c o r d O u t
5. Select "Video In" and use the left/right arrow buttons to select the video input
connector you want to assign to the Source Selector button. Press the OK button.
(Note: If you select an HDMI connector for the Video connection the Audio connection
will automatically change to the same HDMI connector.)
S o u r c e S e t u p
S o u r c e
T i t l e
V i d e o I n
A u d i o I n
T o n e
B a s s
T r e b l e
N i g h t M o d e
R e c o r d O u t
6. Select "Audio In" and use the left/right arrow buttons to select the audio input connector
you want to assign to the Source button. (Note: If you have assigned an HDMI Video
connector for the Source button you cannot assign a different Audio connector.)
S o u r c e S e t u p
S o u r c e
T i t l e
V i d e o I n
A u d i o I n
T o n e
B a s s
T r e b l e
N i g h t M o d e
R e c o r d O u t
7. Repeat steps 4 – 6 for the remaining audio/video connections that you want to re-assign.
You are now ready to enjoy your AVR!
IMPORTANT: For complete set up information, and for complete information about
using all of your audio/video receiver's features and capabilities, download the
AVR 1700, AVR 170, AVR 170/230C Owner's Manual from www.harmankardon.com.
Connections
< C a b l e / S a t e l l i t e >
H D M I 1
H D M I 1
O u t
0
0
O f f
A n a l o g
< C a b l e / S a t e l l i t e >
H D M I 2
H D M I 2
O u t
0
0
O f f
A n a l o g
< C a b l e / S a t e l l i t e >
C o m p o s i t e 1
O p t i c a l 1
O u t
0
0
O f f
A n a l o g