Care And Maintenance - Stanley FATMAX JSCE1S Manual De Instruccion

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

4. When desired pressure is reached, turn off the Compressor Power Switch.
5. Disconnect the adapter from the inflated item.
6. Unscrew and remove the adapter from the Sure Fit
7. Allow the unit to cool before storing away.
WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• Follow all safety instructions found in the "Specific Safety Instructions For Compressors" section of this instruction
manual.
• Recharge this unit fully after each use
USB POWER PORT
1. Press the USB Power Button to turn the USB Port on and the USB power indicator will light.
2. Lift up the cover of the USB Charging Port.
3. Plug the USB-powered device into the USB Charging Port and operate normally.
4. Periodically press the battery charge level pushbutton to check battery status. (When all three battery status indicators light, it
indicates a full battery. When only one red battery status indicator lights, it indicates that the unit needs to be recharged.)
Notes:
This unit's USB Power Port does not support data communication. It only provides 5 volts/2A DC power to an external USB-powered device.
Make sure the USB Power Button is in the off position when the unit is being recharged or stored.
Some household USB-powered electronics will not operate with this unit.
12 VOLT DC PORTABLE POWER SUPPLY
This portable power source is also for use with all 12 volt DC accessories equipped with a male accessory outlet plug and are rated up to
5 amps.
1. Lift up the cover of the unit 's 12 volt DC outlet.
2. Insert the 12 volt DC plug from the appliance into the 12 volt accessory outlet on the unit. DO NOT EXCEED A 5 AMP LOAD.
3. Switch on the appliance and operate as usual.
4. Periodically press the battery charge level pushbutton to check battery status. (When all three battery status indicators light, it
indicates a full battery. When only one red battery status indicator lights, it indicates that the unit needs to be recharged.)
LED AREA LIGHTS
The area lights located on the back of the unit are controlled by the Area Light Power Button. Make sure the area lights are turned off
when the unit is being recharged or stored.
Periodically press the battery charge level pushbutton to check battery status. (When all three battery status indicators light, it indicates a
full battery. When only one red battery status indicator lights, it indicates that the unit needs to be recharged.)

CARE AND MAINTENANCE

All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, we
recommend that the battery is charged at least every 30 days.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the unit with a soft cloth moistened with a mild
solution of water and detergent.
There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and wires. Contact manufacturer to replace
any components that have become worn or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on a number of factors including but not limited to the
number of recharge cycles, and proper care and maintenance of the battery by the end user. Contact manufacturer for any information
you may need.
SAFE BATTERY DISPOSAL
Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly.
Recycling is required. Failure to comply with local, state and federal regulations can result in fines, or imprisonment.
Please recycle.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in
injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
TROUBLESHOOTING
Unit Not Charging
• Make sure all of the unit's functions are turned off.
• Make sure a suitable gage extension cord is properly connected to both the unit and a functioning AC outlet.
nozzle.
®
8 8
Tabla de contenido
loading

Tabla de contenido