Technical Data; Installation Instructions; Symbol Description - Hansgrohe Mediano Showerpipe 26475000 Modo De Empleo/Instrucciones De Montaje

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 7
6
Safety Notes
6 Gloves should be worn during installation to prevent crushing and cutting
injuries.
6 The arm of the shower head is intended only to hold the shower head. Do not
load it down with other objects!
6 Children as well as adults with physical, mental and/or sensoric impairments
must not use this shower system without proper supervision. Persons under the
influence of alcohol or drugs are prohibited from using this shower system.
6 Do not allow the streams of the shower touch sensitive body parts (such as your
eyes). An adequate distance must be kept between the shower and you.
6 The product may not be used as a holding handle. A separate handle must be
installed.
6 The shower system may only be used for bathing, hygienic and body cleansing
purposes.
6 The hot and cold supplies must be of equal pressures.

Installation Instructions

• The fitting must be installed, flushed and tested after the valid norms.
• Prior to installation, inspect the product for transport damages. After it has been
installed, no transport or surface damage will be honoured.
• The installation dimensions stated in these installation instructions are ideal for
people of approximately 1800 mm in body height. The dimensions can be
altered if required. In this case, pay attention to the fact that a change of instal-
lation height will also change the minimum height, and that the altered mounting
dimensions must be taken into consideration.
• Where the contractor mounts the product, he should ensure that the entire area of
the wall to which the mounting plate is to be fitted, is flat (no projecting joints or
tiles sticking out), that the structure of the wall is suitable for the installation of the
product and has no weak points. The enclosed screws and dowels are only suita-
ble for concrete. For another wall constructions the manufacturer's indications of
the dowel manufacturer have to be taken into account.
• The filter insert (97708000) must be used to ensure the standard flow rate and
to protect the hand shower against incoming dirt by pipework. Do you want a lar-
ger water flow rate, then you must use the filter packing (94246000) instead of
the filter insert (97708000). Incoming dirt leads to defects or/and can damage
parts of the hand shower; such caused faults voids all liability and guarantee
claims.
Fault
Insufficient water
Mixer stiff
Mixer dripping
Hot water temperature too low
Instantaneous heater didn't work
4
English
Cause
- Shower filter seal dirty
- Non return valve hasn't moved back
- Cartridge defective, calcified
- Cartridge defective
- Hot water limiter incorrectly set
- Flow limiter in handshower isn't removed
- Filters are dirty
- Non return valve hasn't moved back
Assembly see page 10

Technical Data

Operating pressure:
Recommended operating pressure:
Test pressure:
(1 MPa = 10 bar = 147 PSI)
Hot water temperature:
Recommended hot water temp.:
Thermal disinfection:
Centre distance:
Connections G 1/2:
anti-pollution function
The product is exclusively designed for drinking water!

Symbol description

Do not use silicone containing acetic acid!
Adjustment (see page 13)
To adjust the hot water limiter on single lever mixers, please see page
13. Using a hot water limiter in connection with a continuous flow
water heater is not recommended.
Maintenance (see page 12)
The non return valves must be checked regularly according to DIN
EN 1717 in accordance with national or regional regulations (at least
once a year).
Dimensions (see page 15)
Flow diagram (see page 15)
overhead shower
Hand shower
Spare parts (see page 17)
Cleaning (see page 16) and enclosed brochure
Operation (see page 14)
Remedy
- Clean filter seal between shower and hose
- Exchange non return valves
- Exchange cartridge
- Exchange cartridge
- Set hot water limiter
- Remove flow limiter
- Clean the filter / exchange filter
- Exchange non return valves
max.1 MPa
0,15 - 0,5 MPa
1,6 MPa
max. 80°C
65°C
max.. 70°C / 4 min
150±12 mm
cold right - hot left
Tabla de contenido
loading

Tabla de contenido