Using The Harness - EINHELL AGILLO 36/255 BL Manual De Instrucciones Original

lever. If this is not the case, have the mecha-
nism checked by an expert.
5.6 Guard hood for use with the cutting blade
(Fig. 7)
Caution! The cutting line cover (D) must be re-
moved if you want to work with the cutting blade.
Take care not to cut yourself on the cutting line
cutter.
Slacken the two retaining screws (E) on the cut-
ting line cover.
Start at the side and carefully press in the lugs (F)
and pull the cutting line cover (D) up and off.
5.7 Guard hood for use with the cutting line
(Fig. 7)
Caution! The cutting line cover (D) must be fitted
if you want to work with the cutting line. Take care
not to cut yourself on the cutting line cutter. Start
at the side and press the lugs (F) of the cutting
line cover back in and secure them with the two
screws (E).
5.8 Fitting/removing the cutting blade
The procedure for fitting the cutting blade is
shown in Figs. 8a - 8c. Note the detailed drawing
8d. Warning! Take care not to cut yourself on the
cutting blade.
a) Fitting the cutting blade
Important! If the spacer between the cutting
blade and the motor housing (detailed drawing
8 d / Item 27) slips off the motor shaft (M) during
dismantling, push it back onto the motor shaft as
shown in the drawing.
1. Fit the cutting blade (21) in place.
2. The pressure plate (23) must be fitted with
the higher edge facing the cutting blade (de-
tailed drawing 8d).
3. Fit the pressure plate cover (24).
4. Screw the size M10 hex nut (25) in place.
Warning! For safety reasons, self-locking
nuts are allowed to be used only once without
exception.
5. Press the locking lever (12) and lock the mo-
tor shaft. Tighten the hex nut using the multi-
function tool (22).
6. Check whether the blade (21) can rotate free-
ly after you let go of the locking lever. If this is
not the case, have the mechanism checked
by an expert.
b) Removing the cutting blade
Press the locking lever forward and lock the motor
shaft. Unscrew and the hex nut and remove the
pressure plate cover, pressure plate and cutting
Anl_Agillo_36_255_BL_SPK13.indb 25 Anl_Agillo_36_255_BL_SPK13.indb 25
GB
blade.
Each time before use, check the following :
•
That the equipment is in perfect condition and
that the safety devices and cutting devices
are complete.
•
That all screws are securely fastened.
•
That all moving parts move smoothly.

5.9 Using the harness

Caution! Always use the harness when working
with the equipment (Fig. 2/Item 20). Always switch
off the equipment before you release the harness
– risk of injury!
•
Fit the harness (Fig. 9)
•
Hook the equipment to the harness (Fig. 10).
•
Adjust to the perfect working and cutting po-
sition using the various harness adjusters on
the harness. The strap attachment (Fig. 11/
Item 4) can be moved on the top part of the
long handle if required. To do so, slacken the
wing nut on the strap attachment, move the
strap attachment and then re-tighten the wing
nut.
•
To establish the optimum length of the har-
ness, you should then make a few swinging
movements without starting the motor (Fig.
12).
The harness is fitted with a quick-release mecha-
nism. Pull the red part of the harness (Fig. 13) if
you need to remove the equipment quickly.
5.10 Installing the battery
Push the rechargeable batteries into the batte-
ry mounts provided on the left and right on the
equipment (Fig. 2/Item 1). The battery will be
heard to click into place when it has been pushed
fully in (Fig. 1). To take out the battery, press the
pushlock button (Fig. 15/Item K) and remove the
battery.
5.11 Charging the battery (Fig. 14)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(D) into the socket outlet. The green LED will
then begin to flash.
3. Insert the battery pack into the charger.
4. In the section entitled „Charger indicator" you
will find a table with an explanation of the LED
indicator on the charger.
- 25 -
16.08.2021 12:06:09 16.08.2021 12:06:09