Tabla de contenido
Idiomas disponibles
Idiomas disponibles
The AMICODE 868 keypad is used for remotely piloting electronic devices.
The keypad has four different channels, corresponding to keys 1, 3, A and B, activating the same
number of devices. Channels 1, 3 and A are protected by a five-digit activation code (PIN), which
must be input to enable transmission. The fourth channel, corresponding to key B, is not PIN-code
protected.
After you have typed in the PIN code, if the sequence is correct, the keypad sounds a long beep,
and you can now access one of the three protected channels (1, 3 and A). Each of the three
channels will be activated for 3 seconds.
If you begin to type in an incorrect sequence, you can at any time type in the correct PIN without
this causing an error. The system allows a maximum of 3 attempts (15 key pressings) before going into
protected mode for 10 seconds. During this time, no code can be input and each pressing on the
keypad corresponds to an error signal (4 consecutive beeps). When the 10 seconds have elapsed,
you can re-input the correct PIN code.
A second security code, called PASSWORD, is available for accessing keypad programming.
T
a r
s n
m
s s i
o i
n
f
e r
q
u
e
n
c
y
y T
p
e
f o
c
o
d
e
P
o
w
r e
u s
p
p
y l
B
t a
e t
y r
i l
e f
2 (
d
a
y l i
a
t c
v i
t a
o i
n
) s
A
b
s
r o
t p
o i
n
o
n
s
a t
n
d
b -
y
P
o r
e t
t c
o i
n
c
a l
s s
i D
m
e
s n
o i
s n
O
p
r e
t a
n i
g
a
m
b
e i
t n
e t
m
p
e
a r
u t
B
a
c
k
t i l
k
e
y
p
a
d
i w
h t
E L
D
s
B
u
z z
r e
o s
u
n
d
s
w
h
e
n
k
e
s y
r p
s e
3
c
h
a
n
n
e
s l
p
o r
e t
c
e t
d
b
y
a
5
O
n
e
i d
e r
t c
c
h
a
n
n
l e
The keypad is provided with a 'basic' configuration which specifies the same PIN code and PASSWORD for all the keypads.
Access to the different programming stages is obtained by simultaneously pressing two keys, which must be held down until the
keypad buzzes to confirm. Remember that the keypad lights up when the keys are pressed for the first time. If you realise you have
made some errors during programming, you can exit programming by simply waiting for the keypad to go OFF. The modifications will
be saved only if all the steps of the desired programming have been carried out.
Before starting to use the keypad, you MUST first of all save the new programming PASSWORD and then the new
PIN code. The PIN code and the PASSWORD must be different. We advise you to indicate the two new codes
AMICODE 868 RADIO KEYPAD
1. DESCRIPTION
2. TECHNICAL SPECIFICATIONS
e r
e s
d
d
g i
t i
a
c
c
e
s s
c
o
d
e
P (
N I
)
3. PROGRAMMING
Do not open the keypad for any reason
Program the keypad before installing it.
PASSWORD: 12345
8
6
8
3 .
5
M
H
z
±
2
0
0
K
H
z
E
n
c
y r
p
e t
d
r
l o
n i l
g
c
o
d
e
f
9
V
a
k l
a
n i l
e
b
t a
e t
y r
~
2
y
e
a
s r
<
2
µ
A
P I
5
4
S
e
e
F
g i
1 .
2 -
° 0
C
÷
+
5
° 5
C
IMPORTANT:
PIN: 12345
IMPORTANT:
below.
4
r o
e s
- f l
e l
a
n r
n i
g
Fig.1
Tabla de contenido
