Master Section; Master Volume - HH Tensor-GO Manual Del Usuario

Channel 1 & 2 are universal Mic/Line input channels that will accept a wide variety of sources.
(1) INPUT SOCKETS: Combi input sockets allow for the use of both XLR and 1/4" Jacks,
and accepts balanced and unbalanced signals. Note: a stereo signal on TRS lead cannot be connected
directly.
(2) LEVEL: Use to set the channel level.
an input and then slowly turning up to desired level.
(3) MIC/LINE SWITCH: This switch adjusts the channel gain structure to suit either
microphones (or other low level devices) or higher line level devices. Always select this before
adjusting the channel level.
(4) REVERB: This switch routes the channels signal to the internal reverb module.
Channel 3/4 is a stereo input channel for line level devices. All
LEVEL
sockets may be used at the same time.
0 10
(5) AUX INPUTS: A 3.5mm stereo socket for connecting auxiliary audio from a source such as a mobile
device.
(6) RCA INPUTS: A pair of RCA phono sockets for connecting a line level source with RCA terminals
PUSH
TO LINK
HOLD TWS (7) Bluetooth: Press to enable the integrated Bluetooth functionality. The LED will blink while in pairing
mode. Look for 'HH-Tensor' on your device. Once connected the LED will stay on.
L R
Tensor-Go also supports TWS wireless stereo linking over Bluetooth with two Tensor-GO systems. TWS
allows stereo audio to be routed from your mobile device to a pair of Tensor-Go systems providing rich true
stereo sound. Connect your device to the first system as above, then press and hold the Bluetooth button
AUX
for two seconds to enable TWS mode. On the second system, press and hold the Bluetooth button and the
system will auto find and pair. Note, only Bluetooth audio is routed over TWS, not any hardwired inputs
CHANNEL 3/4
such as mics.
(8) LEVEL: Use to set the channel level.
desired level. For Bluetooth connections, adjust your devices volume to maximum for the best signal.

MASTER SECTION

(9) MASTER VOLUME: Controls the overall listening level of your Tensor-GO system.
Note: Set this control to minimum when switching the unit ON or Off.
(10) POWER: Illuminated green when the system is powered up.
(10) LIMIT: Tensor-GO is equipped with an onboard limiter to prevent overload to the power
amplifiers and loudspeakers. The Limit LED will illuminate red when the Limiter is active.
Occasional blinking of the Limit led is ok, but continuous illumination should be avoided by
reducing the Master Volume slightly.
(11) MODE: Four presets are included to optimise the response of the Tensor-GO to suit your
needs. Cycle through them using the Mode button.
MUSIC: A Bass and Treble lift with flat mids
BAND: A Bass lift with flat mids and highs
NATURAL: A Treble lift with flat lows and mids
SPEECH: A bass roll-off with flat mid and upper frequencies to
ensure clarity on vocals.
(12) REVERB: Set the overall level of reverb with this control. Ensure
you have routed a channel to the reverb with (4) first.
(13) MIX OUT: A pre master volume signal feed which can be used to
connect a second Tensor-GO, Stage monitor, house PA or recording
console for example. The MIX OUT signal level is not affected by the
VOLUME CONTROL.
© 2021 HH Electronics Ltd
Note, always set the Level to minimum before connecting
Note, always set the Level to minimum before connecting an input and then slowly turning up to
Designed and Engineered in the UK by HH Electronics LTD.
LEVEL LEVEL
0 10 0
LINE LINE
MIC MIC
REVERB REVERB
CHANNEL 1 CHANNEL 2

MASTER VOLUME

MODE
MUSIC
BAND
0 10
NATURAL
SPEECH
POWER / LIMIT
0 10
REVERB MIX OUT
MUSIC
BAND
NATURAL
SPEECH
EN
10
6