Installation Procedure - Franke 3590040 FSBS 6001 N ID XS A+ Instrucciones Para El Uso E Instalacion

How to install Water Line
1. The water pressure should be 2.0~12.5 kgf/cm
automatic icemaker.
* Checkup your tap water pressure ; if a cup of 180cc is full
within 10 seconds, the pressure is OK.
2. When installing the water tubes, ensure they are not close to any
en hot surfaces.
3. The water filter only filters water ; it does not eliminate any
bacteria or microbes.
4. If the water pressure is not so high to run the icemaker, call
the local plumber to get an additional water pressure pump.
5. The filter life depends on the amount of use. We recommend you
replace the filter at least once every 6months.
* Quando si monta il filtro, scegliere una posizione che ne
consenta un agevole accesso.
6. After installation of refrigerator and water line system, select
[WATER] on your control panel and press it for 2~3 minutes to
supply water into the water tank and dispense water.
6. Use sealing tape to every connection of pipes/tubes to ensure
there is no water leak.
7. The water tube should be connected to the cold water line.

Installation Procedure

(Dispenser Models Only)
1. Join Connector to the tap water line
<Figure A>
Connector B
Connector A
Tubber Packing
Water Tube
Place the rubber washer inside the tap connector and screw onto the water tap.
2. Get ready to install the Water Filter
1) Measure an approximate distance between the filter and the Water
Tube and cut the tube off filter vertically.
2) Connect the tubes to the filter as the figure shows.
Leave a sufficient distance when cutting the tubes.
All manuals and user guides at all-guides.com
(Dispenser Models Only)
2
or more to run the
WATER SUPPLY KIT
❈ Check the parts below for installing water supply.
Some other necessary parts are available at your local
service agents.
Connector
(3014454520)
Fastener X ea
Screw X 4ea
(3011202000)
(7112401211)
Filter box Water tube A/B
(3019974100) (A:3019503200
B:3019503300)
<Figure B> Tap
Tap
Connector A
Tubber Packing
Water Tube
Tap Side
Water Tube
Filter Box
A right angle
46
3.Remove any substances in the filter.
1) Open the main tap water valve and check if water comes out
of the Water Tube.
2) Check if the Water Valve is open in case water does not come
out.
3) Leave the valve open until clean water is coming out.
* Initial water may contain some substances out of filter
(manufacturing process).
4. Attach the Filter Box
Holder
1) Screw and fasten the filter holder to the left/right side of the
(3012020700)
backof refrigerator.
* In case the holder is not fastened well, remove the back paper
of the tape on the filter holder and attach it.
2) Insert the filter box into the holder.
5. Connect the Water Tube to the refrigerator.
1) Remove the rear cover at the bottom back of the refrigerator.
2) Insert the fastening ring into the Water tube.
(Be careful to follow the direction of the nut.)
3) Insert the Water Tube into the top of the Water Valve, turn the
nut clockwise to fasten it. (The Water valve is to the right of the
motors.)
4) Check for any bent tubes or water leaks; if so, re-ckeck
instalation procedure.
5) Replace the rear cover. (The Water Tube should be placed
between the groove of the refrigerator back and motor cover.)
Set the tube upright as the figure shows.
6. Fasten the Water Tube.
1) Fasten the Water Tube with the [Fastener A] .
2) Check if the tube is bent or sqeezed. If so, set it right to
prevent any water leak.
7. After installation of Water Supply System
1) Plug in the refrigerator, press the [WATER] button on the
control panel for 2~3 minutes to remove any air (bubble) in the
pipes and drain out the initial water.
2) Check for the water leaks again through the water supply
system (tubes, connectors and pipes) Rearrange the tubes
again and do not move the refrigerator.
Hot Water
Water Tube
Reaf. Side
Water Tube
Water
Water Tube
Water Tube
Nut
Water Valve
Fastener A
Water Tube
Tap
Connector
Water Tube
47
en