Removing The Guard; Preparation Before Use - Stanley FATMAX FMEG225VS Traducido De Las Instrucciones Originales

ENGLISH (Original instructions)
If the system impedance of the power supply is lower than
0.107 Ω, disturbances are unlikely to occur
Features
This tool includes some or all of the following features.
1. On/off switch
2. Spindle lock
3. Guard
11. Variable speed dial
12. Side handle
Soft start feature
The soft start feature allows a slow speed build-up to avoid
an initial jerk when starting. This feature is particularly
useful when working in confined spaces.
No-Volt
The No-volt function stops the grinder restarting without the
switch being cycled if there is a break in the power supply.
Assembly
Warning! To prevent accidental operation, turn off and
unplug tool before performing the following operations.
Failure to do this could result in serious personal injury.
Attaching and removing the wheel guard
(Fig A)
Warning! To minimize the danger of serious personal injury,
please switch off the tool power and disconnect all plugs
before adjusting or removing/installing any accessory. Before
reassembling the tool, press and release the trigger switch to
make sure the tool is already switched off.
Attaching and guard
Place the angle grinder on a work bench, groove facing
u
up.
Bring the flange of the guard (3) collar over the groove
u
(9) of the gear housing.
Turn the guard (3) counterclockwise by 150 degrees.
u
Make sure that the screws (10) are tightened.
u

Removing the guard

Loosen the screws (10) on the guard collar.
u
Pull up the guard (3).
u
Warning! Do not operate the tool when the safety
guard is not in place.
Note: Refer to the grinding accessories chart at the end of
this section for accessories that can be used together with
this angle grinder.
Attaching and removing grinding wheels
(Fig B, C)
Warning! Do not use damaged grinding wheels.
8
Place the tool on a work bench, groove facing up.
u
Fig C: Attach the inner flange (4) correctly on the output
u
shaft (5).
Place the grinding wheel (6) on the inner flange (4).When
u
attaching a grinding wheel with a raised center, make sure
that the raised center (7) faces the innerflange (4).
Fig C: Tighten the outer flange (h) until the output shaft
u
(5).
When attaching the grinding wheel, the ring on top ofthe
u
outer flange (8) must face the wheel.
Press the spindle lock (2) and prevent the spindle (4)
u
from rotating until it locks in place.
Use the pin spanner to tighten the outer flange (8).
u
Attaching the Side Handle
Warning! Before using the tool, check that the handle is
tightened securely.
Warning! The side handle (12) should always be used to
maintain control of the tool at all times.
Screw the side handle (12) tightly into one of the holes on
either side of the gear case.

Preparation before use

Attach the safety guard and appropriate abrasive or
u
grinding wheels. Do not use abrasive or grinding wheels
that are overly worn.
Make sure that the inner and outer flanges are attached
u
correctly.
Make sure that the abrasive or grinding wheels are
u
rotating in the direction of the arrows on the accessories
and tool.
Use
Warning! Always observe the safety instructions and
applicable regulations.
Warning! To minimize the danger of serious personal injury,
please switch off the tool power and disconnect all plugs
before adjusting or removing/installing any accessory.
Before reassembling the tool, press and release the trigger
switch to make sure the tool is already switched off.
Warning:
Make sure all materials to be grinded are secured in
u
position.
Apply slight pressure to the tool. Do not apply side
u
pressure to the abrasive disc.
Avoid overloading. If the tool becomes hot, let it spin for
u
a few minutes with no load.
Be sure to hold the tool tightly with both hands (one
u
hand on housing, the other on side handle).
Start the tool and bring the grinding wheel on the
workpiece.
Keep the edge of the wheel tilted at angle from 15 to 30
u
degrees against the surface of the workpiece.