Toona 4 Serie Instrucciones De Instalación página 16

maximum opening angle of the leaf. Important – The values of A and B
must be similar to allow linear movement of the automation.
01. Measure dimension C (fig. 4) on the fixing side;
02. On graph 2, identify dimension C found and trace a horizontal line that
determines the value of dimension B (*) as shown in the example of fig.
5; the meeting point with line "r.i.l" (installation line recommended) deter-
mines the value of the angle of maximum opening. From this point, trace
a vertical line as shown in the example of fig. 5 to determine the value of
dimension A.
If the angle found does not correspond to the requirements, adapt dimen-
sion A and if necessary dimension B, so they are similar.
(*) Do not use values of dimension B below the line "t" (see graph 2).
03. Before being fixed to the wall the bracket must be sealed to the specific
fixing plate (fig. 7); if necessary the bracket can be cut adapting values of
dimensions A and B.
Note – The bracket supplied for the Toona series 4-5 gear motor, mea-
sures 150 mm in length; in the event of special applications or in the event
of a gate equipped with external opening (fig. 6) use bracket mod. PLA6
(accessory).
CAUTION! – Before securing the rear bracket, check the fixing
zone of the front bracket is in a solid part of the leaf, as this bracket
must be fixed at a different height of the rear bracket (fig. 8).
04. At this point, fix the bracket using dowels, screws and washers required
(not supplied).
3.5.2 – Installation of front fixing bracket
The front bracket must be fixed to the gate leaf respecting the values of dimen-
sions D and E (Fig. 4).
Note – The bracket supplied for the Toona series 4-5 gear motor must be
welded directly to the gate leaf. If this is not possible, use bracket mod. PLA8
(accessory).
01. Establish the value of dimension E using Table 1;
02. Establish the height in which to position the front bracket, referring to fig. 8;
03. Fix the bracket to the solid part of the gate leaf.
3.5.3 – Installation of the gear motor on the fixing brackets
• Installing the gear motor on the rear bracket:
01. Fix the gear motor to the bracket as shown in fig. 9 using the screw,
washer and nut supplied;
02. Tighten the nut to the end and then loosen by 1/10 of a turn to allow
minimum clearance between the parts.
• Installing the gear motor on the front bracket:
01. Fix the gear motor to the bracket as shown in fig. 10 using the screw,
TO4005 TO4006
D (mm):
730 695
A (mm)
100
630 595
110
620 585
120 610 575
130 600 565
140 590 555
150 580 545
160
570 535
170
560 525
180
550 515
190
540 505
200 530 495
210 520 485
220
230
240
250
260
270
280
2 – English
Toona 4
TO4015 TO4605 TO4024
730 730 730
E (mm)
630 630 630
620 620 620
610 610 610
600 600 600
590 590 590
580 580 580
570 570 570
560 560 560
550 550 550
540 540 540
530 530 530
530 530 530
washer and nut supplied;
02. Tighten the screw to the end.
03. Fix the label provided in the package, dealing with the unblocking and
blocking operations of the gear motor, permanently close to the gear motor
3.6 - Setting the mechanical limit switch
The mechanical limit switch allows to set the stop position of the gate leaf, in
this way, it is not necessary to use the stop blocks and the leaf does not hit
against these at the end of the manoeuvre.
• Toona series 4-5 (24 V)
WARNING – In the event of applications with a gate equipped with
opening towards the outside (fig. 6) it is necessary to invert the power
supply wires. Set the limit switch in Opening of the gear motor as follows:
01. Unblock the gear motor as shown in fig. 16;
02. Loosen the mechanical stop screw;
03. Bring the gate leaf manually to the Open position required;
04. Then, bring the mechanical stop to the end of the pin and block the screw
(fig. 11).
05. Bring the leaf manually to the Close position and block the gear motor.
Note – Gear motors mod. TO4006 and mod. TO5016, are provided with
a mechanical limit switch also for the Closing manoeuvre. If in posses-
sion of one of these models, to set the mechanical limit switch repeat the pro-
cedure described above, with a variation at point 03, in this case, bring the
gate leaf manually in the required Closing position.
• Toona series 4-5 (230 V)
The Toona series 4-5 gear motors arranged for an alternate current of 230V,
come with mechanical stop with micro switch which, on contact with the pin
interrupts the electrical power supply. WARNING – In the event of applica-
tions with a gate equipped with opening towards the outside (fig. 6) it is
necessary to invert the power supply wires.
• Toona series 6-7
Set the limit switch in Opening and Closing of the gear motor;
01. Unblock the gear motor as shown in fig. 16;
02. Move the leaf manually until the mechanical stop screw is visible and loos-
en the screw;
03. Bring the gate leaf manually to the Open position required;
04. Then, bring the mechanical stop to the end of the pin and block the screw
(fig. 12);
05. At this point repeat this procedure bringing the leaf manually to the position
of maximum Closure, to set the limit switch in Closure;
06. Finally, block the gear motor.
TABLE 1
Toona 5
TO5015 TO5016 TO5605
880 845 880
E (mm)
780 745 780
770 735 770
760 725 760
750 715 750
740 705 740
730 695 730
720 685 720
710 675 710
700 665 700
690 655 690
680 645 680
670 635 670
660 625 660
650 615 650
640 605 640
630 595 630
620 585 620
610 575 610
600 565 600
Toona 6-7
TO5024 TO5024I
TO5024HS
880 880
E (mm)
780 780
770 770
760 760
750 750
740 740
730 730
720 720
710 710
700 700
690 690
680 680
670 670
660 660
650 650
640 640
630 630
620 620
610 610
600 600
1070
890
880
870
860
850
840
830
820
810
800
790