Hoover op60alg011 Manual De Instrucciones página 5

#1
NOTE: Dust pick up ability carpet, dust pick up ability hard floor, and energy efficiency
in accord with Commission Regulations (EU) 665/2013 and (EU) 666/2013.
All accessories can be fitted to the end of the handle or the end of the telescopic tube.
Accessory Set* – The Crevice tool, Furniture nozzle and Dusting brush can be stored on
tube thanks to the practical tool holder*.
Crevice Tool* – For corners and hard to reach areas. [X1]
Dusting Brush* – For bookshelves, frames, keyboards and other delicate areas. To
extend the brushes push the button on the body of the tool. [X2]
Furniture Nozzle* – For soft furniture and fabrics. [X3]
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hairs removal. [Y]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for
deep cleaning on textile surfaces and other hard to clean areas, particularly suitable for
allergen removal. [Z]
Parquet Nozzle* – For parquet floors and other delicate floors. [AA]
IMPORTANT: Do not use mini turbo nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while brush is rotating.
CLEANER MAINTENANCE
Replacing the Dust Bag
If the bag check indicator is red please check and, if necessary, replace the bag.
1. Lift the bag door release latch to open the bag door, pull the bag holder and pull the
bag collar to remove the bag. [12,13]
2. Apply the peel and seal the sticker, located on the bag collar, to the bag inlet. The full
dust bag should be disposed of correctly and carefully. [14,15]
3. Fold a new bag as shown on the bag and fit by inserting the collar into the bag holder.
4. Refit the bag holder and close the bag door.
WARNING: The bag door will NOT close if the dust bag and/or the bag holder are not
assembled to the cleaner. Always ensure the bag and bag holder are present when
closing the bag door.
REMEMBER: The LED bag check indicator* may also be lit if an obstruction has occurred.
In this case, refer to'Remove a Blockage From the System'.
Cleaning the Filters*
To maintain optimum performance of your cleaner, please wash the filters after each 5
bag changes.
*Certain Models Only **May vary according to the model
Cleaning the pre-motor filter:
1. Lift the bag door release latch to open the bag door and remove the bag holder. [13]
2. Remove the pre-motor filter frame from the cleaner. [16]
3. Remove the filter sponge from the holder. [17]
4. Wash it in hand warm water, and allow it to dry thoroughly before inserting into the
cleaner. [21, 22]
Cleaning the exhausted filter and exhaust sponge filter:
1. To remove the exhaust filter sponge and the exhaust filter, remove the exhaust
sponge 1 from the exhaust cover, unclip the filter pack and remove the other sponge
2. [18, 19, 20]
2. Wash them in hand warm water, and allow them to dry thoroughly before replacing.
[21, 22]
REMEMBER: Do not use hot water or detergents. In the unlikely event of the filters
becoming damaged, fit a Genuine Hoover replacement. Do not try and use the product
without a dust bag or filter fitted.
Cleaning the permanent cloth dust bag*
To maintain optimum performance we recommended that you wash the permanent cloth
dust bag under warm water after every 5 full bags. Remove excess water and leave to
dry fully before replacing.
Removing a blockage from the system (*Certain models only)
If the bag check indicator LED is illuminated or flashing:
1. Check if the bag is full. If so, refer to 'Replacing The Dust Bag'.
2. If it is not full, then:
A. Do the filters need cleaning? If so, refer to 'Cleaning the Filter'.
B. Check if there is any other blockage in the system - Use a cord or a pole to
remove any blockage from the telescopic tube or flexible hose.
WARNING - The LED bag check indicator will turn on if the cleaner is used when full, if
there is a blockage or if the filters are dirty. If the cleaner is used for a significant period
of time with the bag LED check indicator is on, a thermal cut out will switch the cleaner
off to prevent overheating. The LED bag check indicator turns off once the cleaner has
switched off to signal that the thermal cut out has been activated. If this should happen,
switch the cleaner off, unplug and correct the fault. It will take about 30 minutes for the
cut out to automatically reset.
3
GB