Black and Decker KG711 Manual Del Usuario página 8

ENGLISH
guard for cutting operations part numbers 1004702-27 and
1004702-28 for KG711/KG911 and KG912/KG752 is available
and can be obtained from BLACK+DECKER service centres.
Fitting and removing the guard (fig. A)
KG912 Only
The tool is supplied with a guard intended for cutting off
purposes only. If the unit is intended to perform grinding
operations, a guard specific for this operation must be fitted. A
suitable guard for grinding operations part number 1004702-36
is available and can be obtained from BLACK & DECKER
service centres.
Fitting
Place the angle grinder on a table, spindle (5) up.
u
Align the lugs (8) with the notches (9).
u
Press the guard (4) down and rotate it to the required
u
position.
Securely tighten the screw (6).
u
To remove the guard, slacken the screw
u
Warning! Never use the tool without the guard.
Fitting the side handle
Screw the side handle (2) into one of the mounting holes
u
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs
(fig. B - D)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size (see
technical data).
Fitting
Fit the guard as described above.
u
Place the inner flange (10) onto the spindle (5) as shown
u
(fig. B). Make sure that the flange is correctly located on
the flat sides of the spindle.
Place the disc (11) onto the spindle (5) as shown (fig. B).
u
If the disc has a raised centre (12), make sure that the
raised centre faces the inner flange.
Make sure that the disc locates correctly on the inner
u
flange.
Place the outer flange (13) onto the spindle. When fitting
u
a grinding disc, the raised centre on the outer flange must
face towards the disc (A in fig. C). When fitting a cutting
disc, the raised centre on the outer flange must face away
from the disc (B in fig. C).
Keep the spindle lock (3) depressed and tighten the outer
u
flange using the two-pin spanner (14) (fig. D).
8
(Original instructions)
Removing
Keep the spindle lock (3) depressed and loosen the outer
u
flange (13) using the two-pin spanner (14) (fig. D).
Remove the outer flange (13) and the disc (11).
u
Fitting and removing sanding discs (fig. D & E)
For sanding, a backing pad is required. The backing pad is
available from your BLACK+DECKER dealer as an accessory.
Fitting
Place the inner flange (10) onto the spindle (5) as shown
u
(fig. E). Make sure that the flange is correctly located on
the flat sides of the spindle.
Place the backing pad (15) onto the spindle.
u
Place the sanding disc (16) onto the backing pad.
u
Place the outer flange (13) onto the spindle with the raised
u
centre facing away from the disc.
Keep the spindle lock (3) depressed and tighten the outer
u
flange using the two-pin spanner (14) (fig. D). Make sure
that the outer flange is fitted correctly and that the disc is
clamped tightly.
Removing
Keep the spindle lock (3) depressed and loosen the outer
u
flange (13) using the two-pin spanner (14) (fig. D).
Remove the outer flange (13), the sanding disc (16) and
u
the backing pad (15).
Use
Warning! Let the tool work at its own pace. Do not overload.
Carefully guide the cable in order to avoid accidentally
u
cutting it.
Be prepared for a stream of sparks when the grinding or
u
cutting disc touches the workpiece.
Always position the tool in such a way that the guard
u
provides optimum protection from the grinding or cutting
disc.
Switching on and off
To switch on, slide the on/off switch (1) forward. Note that
u
the tool will continue running when you release the switch.
To switch off, press the rear part of the on/off switch.
u
Warning! Do not switch the tool off while under load.
Soft Start Feature
The soft start feature allows a slow speed build-up to avoid
an initial jerk when starting. This feature is particularly useful
when working in confined spaces.
No-Volt
The No-volt function stops the grinder restarting without the
switch being cycled if there is a break in the power supply.