Safety Instructions; General Safety Warnings; Using Your Appliance - Stanley FATMAX FME790 Manual De Instrucciones

ENGLISH
Intended use
Your Stanley Fat Max FME790 mitre saw stand has been
designed for use with a Stanley Fat Max mitre saws. This tool
is intended for professional and private, non professional
users

Safety instructions

@

General safety warnings

Warning! Read all safety warnings and all
instructions.
Read all of this manual carefully before using the
u
appliance.
The intended use is described in this manual. The use of
u
any accessory or attachment or the performance of any
operation with this appliance other that those
recommended in this instruction manual may present a
risk of personal injury.
Retain this manual for future reference.
u

Using your appliance

Always take care when using the appliance.
This appliance is not intended for use by persons
u
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
The appliance is not to be used as a toy.
u
Use in a dry location only. do not allow the appliance to
u
become wet.
Do not immerse the appliance in water.
u
Do not open body casing. There are no user serviceable
u
parts inside.
Do not operate the appliance in explosive atmospheres,
u
such as in the presence of flammable liquids, gases or
dust.
After use
When not in use, the appliance should be stored in a dry,
u
well ventilated place out of the reach of children.
Children should not have access to stored appliances.
u
When the appliance is stored or transported in a vehicle it
u
should be placed in the boot or restrained to prevent
movement following sudden changes in speed or
direction.
Inspection and repairs
Before use, check the appliance for damaged or defective
u
parts. Check for breakage of parts, damage to switches
and any other conditions that may affect its operation.
4
(Original instructions)
Do not use the appliance if any part is damaged or
u
defective.
Have any damaged or defective parts repaired or replaced
u
by an authorised repair agent.
Never attempt to remove or replace any parts other than
u
those specified in this manual.
In case of any missing parts, do not assemble the stand
u
until the missing parts are obtained and are correctly
installed.
Additional safety instructions for mitre saw stand
Fully assemble and tighten all the fasteners required for
u
this stand. Also occasionally check the stand and make
sure the mitre Saw is still tight. An unstable loose stand
may shift in use and result in serious injury.
Before operating, make sure the entire unit has been
u
placed on a flat and solid level surface. If tool with stand is
unstable and tips, serious injury may occur.
Never STAND on tool or its stand or use them as a ladder
u
or scaffolding. Serious injury could occur if the tool is
tipped or the cutting tool is contacted accidentally. Do not
store materials in a position on or near the tool where it
necessary to stand on the tool or its stand to reach them.
Use only our replacement parts. Any others may cause a
u
hazard. The mitre saw should be mounted to the stand
firmly according to the instruction manual. Properly align,
position and balance the mitre saw according to the
instruction manual after mounting the mitre saw to the
stand.
Never modify the stand in any manner or use the stand for
u
any purpose other than is stated in the instructions.
Cutting material may cause the stand to become
u
unbalanced, always make sure the material is properly
supported. If the piece being cut is placed far beyond the
Work Support, the stand legs on the opposite side may be
lifted up suddenly due to weight imbalance. Firmly Hold
the opposite side before cutting to prevent this situation.
Warning! For your safety, never connect to power source until
all assembly steps are complete and you have read and
understood the entire owner's manual.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or
u
accessories.
Injuries caused by prolonged use of a tool. When using
u