Personal Protection - Black and Decker KA225 Manual De Instrucciones

ENGLISH
Additional safety instructions for sanders
Always wear a dust mask whenever sanding.
Thoroughly remove all dust after sanding.
Before using the tool on wooden workpieces, make sure
to fit the dustbag.
Before using the tool on metal workpieces, make sure to
remove the dustbag.
Never use the tool without a sanding sheet.
Never use the tool without a sanding base.
Sanding lead-based paint or MDF
Sanding of lead-based paint is not recommended due to the
difficulty of controlling the contaminated dust. The greatest
danger of lead poisoning is to children and pregnant women.
Any pre-1960 building may in the past have been painted with
paint containing lead. This paint may be covered with additional
layers of paint. Before starting work, it is important to
determine whether the paint to be sanded contains lead.
This can be done using a test kit or by a professional decorator.

Personal protection

Do not let children or pregnant women enter the work area.
Wear a dust mask specifically designed for protection
against lead paint dust and fumes and ensure that persons
within or entering the work area are also protected.
Do not eat, drink or smoke in the work area. Do not store
any food or drink in the work area.
Wash yourself very carefully before eating, drinking or
smoking.
Environment
Remove the paint in such a way that the amount of dust is
minimised.
Seal the work area with plastic sheeting.
Minimise the amount of dust outside the work area.
Cleaning
Thoroughly vacuum and clean all surfaces in the work
area every day.
Regularly change the dustbag and filters of the vacuum
cleaner.
Thoroughly wash any foreign objects exposed to dust
before using them again.
Additional safety instructions for Australia and New
Zealand
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
4
Features
This tool includes some or all of the following features.
On/off switch (1)
Variable speed control (2)
Round base (3)
Pointed base (4)
Dustbag (5)
Louvre attachment (fig. J)
Assembly
Warning! Make sure that the tool is switched off and unplugged.
Round base
With this sanding base, you can use the tool as a random orbit
sander (fig. H).
Fitting and removing the sanding base (fig. A)
Place the sanding base (3) onto the spindle (6).
Place the washer (7) onto the spindle.
Insert the screw (8) into the hole in the spindle and
tighten the screw using the Allen key (9) supplied.
To remove the sanding base, remove the screw and washer.
Fitting sanding sheets (fig. B)
Hold the tool with the sanding base (3) facing upwards.
Press the sanding sheet (10) onto the sanding base.
The holes in the sheet do not need to line up with the
holes in the base.
Pointed base
With this sanding base, you can use the tool as a detail
sander or an orbital sander.
Fitting and removing the sanding base (fig. C & D)
Place the sanding base (4) onto the spindle (6). For detail
sanding, the pointed end should face forward as in fig. C.
For sanding large areas, the pointed end should face to
the back as in fig. D.
Make sure that the legs of the base locate into the tool.
Place the washer (7) onto the spindle.
Insert the screw (8) into the hole in the spindle and
tighten the screw using the Allen key (9) supplied.
To remove the sanding base, remove the screw and
washer.
Fitting sanding sheets (fig. E)
Detach the two diamond-shaped tips (11) from the
sanding sheet (12).
Hold the tool with the sanding base facing upwards.
Place the sanding sheet (12) onto the sanding base,
making sure that the holes in the sheet line up with the
holes in the base.