Scan Mode - Miniland digital camera 2.4 Manual De Instrucciones

Note: The light sensor (II) is located at the top of
the camera. Take care not to cover the sensor with
any object to prevent the camera from entering night
mode when there is light in the room.
5.2.3. CHOOSING THE CAMERA
This product is designed to allow the observation of
different areas with up to 4 cameras. To choose the
camera you want to see, follow the next steps:
1. Press the Menu/Back key
will pop up;
2. Press the UP or DOWN
icon is highlighted then press RIGHT key to enter
into the sub-menu;
3. Press UP or DOWN
camera icon then press RIGHT
sub-menu;
4. Press RIGHT /LEFT
select the desired camera to view (Camera 1, camera
2, camera 3 or camera 4);
5. Press key go to selected cam.
Note: There is a faster way to change the camera you
are viewing. Directly press
paired cameras: CAM1 / CAM2 / CAM3 / CAM4 /

SCAN MODE.

5.2.4. SCAN MODE
This function automatically cycles through your paired
camera channels to display each camera for 12
seconds. This function can be used only when you
have more than 1 camera unit paired. To enter in this
mode:
1. Press the Menu/Back
pop up;
2. Press the UP or DOWN
icon is highlighted then press RIGHT key to enter
into the sub-menu;
3. Press UP or DOWN
camera icon then press RIGHT
sub-menu;
4. Press RIGHT /LEFT
select the scan camera icon
5. Press key.
Note: When one of the cameras is out of range or is
not switch on, the monitor will warn you and the Scan
Mode will stop.
Note 1: Scan mode can be activated/deactivated by
pressing while visualizing the main screen.
5.2.5. DUAL MODE
The function will display two cameras on the screen at
the same time. It only can be used when there is more
than 1 camera unit paired.
1. Press the Menu/Back
pop up;
2. Press the UP key or DOWN
camera icon is highlighted then press RIGHT
to enter into the sub-menu;
3. Press UP or DOWN
camera icon then press RIGHT
sub-menu;
and the menu icon
key until the camera
key to select VIEW
key enter into the
/UP /DOWN key to
key to cycle through
key and the menu will
key until the camera
key to select VIEW
key enter into the
/UP /DOWN key to
;
key and the menu will
key until the
key to select VIEW
key enter into the
4. Press RIGHT
select the dual view icon
5. Press key go to dual mode.
Note: At the dual view mode, you won't be able to use
the bidirectional function and you will hear only the
camera you have selected.
Note 2: A red frame will appear on the image
selected. To see the image of one of the two cameras
full-screen, select with the RIGHT
which one you want to see and press
Note 3: If you have more than 2 cameras paired to
the same monitor, press RIGHT
which ones you want to see.
5.2.6. ADD CAMERA AND PAIRING
The pairing between the monitor and the camera will
be done under two circumstances:
- If you want to add an additional camera.
This product is designed to allow the observation of
different areas with up to 4 cameras.
- If the monitor and the camera are not paired.
The monitor and the original camera leave the
factory with channel 1 programmed, nonetheless,
if for some reason, they are not, you can link them
manually following the steps indicated below.
To pair the camera and the monitor follow the next
steps:
1. Press the MENU/Back
pop up;
2. Press the UP
camera icon
to enter into the sub-menu;
3. Press UP
icon then press RIGHT
menuen;
4. Press RIGHT
select the desired camera to add;
5. Press key to search for a camera unit. The LED
indicator (2) will begin to flash in green.
6. While the LED indicator is flashing, press the link
button on the camera (5).
7. Once paired, the LED indicator will stop flashing
and the image of the camera will show immediately
on the monitor unit screen;
8. If unsuccessful, please repeat above steps;
For various reasons you may lose the connection
between the monitor and a camera which is already
connected. Should this be the case, repeat the
process explained above to connect the camera with
the monitor again.
Note: Before starting the pairing process, make sure
that the camera and the monitor are close to each
other.
key
Note 2: Each camera can be linked just with one
monitor at a time.
Nota 3: If the monitor and the camera, for some
reason, have left the factory without being paired,
you will have to do it manually adding the camera to
11
ENGLISH
/LEFT /UP /DOWN
;
or LEFT
key and the menu will
key or DOWN
is highlighted then press RIGHT
or DOWN key to select ADD camera
key enter into the sub-
/LEFT /UP /DOWN
key to
and LEFT key
key.
to select
key until the
key
key to