Idiomas disponibles
Idiomas disponibles
6. C ut the landing with the muley saw, taking the utmost care not to chip the floor; sand off any imperfections on
the edge with sandpaper and protect with the wood stain provided.
assembly
7. D etermine the position of the central column on the floor in relation to the dimensions of the previously cut
landing and then fit the base 023012 (Fig. 2).
8. D rill a hole using a 14ÿ bit and fasten the base 023012+012009+022001 to the floor with the parts 008001
(Fig. 1) .
9. Screw the tube 042013 onto the base 023012+012009+022001(Fig. 1).
10. Fit the base cover 132017 or 132018 on the tube 042013 (Fig. 10).
11. F it in order the spacer 130210 or 130211, with the parts 023041 or 023040 already assembled, the plastic
spacers 131030 or 131031, the first tread 103008 (with the wooden slats parallel to the pre-established
ascending side (Fig. 10), remembering that the staircase ascending direction is given by the shape of the
handrails), the spacer 130210 or 130211, with the parts 023041 or 023040 already assembled, the plastic
spacers 131030 or 131031 and again the tread (with the wooden slats parallel to the pre-established
ascending side) 103008, and so forth. Position the treads, alternating between right and left, so that the weight
is evenly distributed (fig. 9).
12. O nce you have reached the end of the first tube 042013, screw on the part 022003, screw on the next tube
042013 and continue assembling the staircase (Fig. 9).
13. O nce you have reached the end of the tube 042013, screw the part 022001 onto the part 046036 keeping the
threaded hole facing up (screw on the part 046036 taking into account that it must be at the same height as
the landing floor). Continue fitting the treads using the compensation part 023001 in the plastic spacer 130210
or 130211 already assembled with the parts 023041 or 023040 and the plastic spacers 131030 or 131031
(Fig. 11).
14. C ut the part 023001 about 3 mm from the edge of the shortest part, and fit it to the spacer 130210 or 130211
and then fit the landing 088002. Position the landing with the small hole (which will be used to fit the baluster)
on the landing side of the treads (Fig. 9).
15. Fit the parts 023035 or 023037, 022065, 009010 and tighten the part 005008 (Fig. 1).
Fixing the landing
16. M ove the part 047009 close to the floor. Determine the position, maintaining a distance of about 15 cm from
the outer edge of the landing, drill a hole using a 14 mm Ø bit and finally fasten using the parts 008001 (Fig. 1).
17. Secure the parts 047009 to the landing using the parts 011053 (drill a hole in the landing using a 5 mm Ø bit).
18. Position the parts 132016 (Fig. 1).
19. Release the part 005008 and fan out the treads 103008. You can now climb the staircase.
Railing assembly
20. S tart fitting the railing from the landing with an end baluster (x) and then with the intermediate balusters (y)
and the joining balusters (z).
If necessary, cut the balusters 127031 or 127035 from the lower side to obtain a railing height of about
100 cm. Orient the balusters with the part 033078 with the drilled part facing up (Fig. 1) (Fig. 8). Tighten the
part 001010 of the lower and upper tread according to the rise (Fig. 1).
21. C heck that all the balusters positioned are vertical. Take care during this operation as it is very important for
successful assembly.
22. Finally tighten the part 005008 (Fig. 8).
23. F asten the part 033142 on the floor in correspondence to the first baluster, drilling a hole using an 8 mm Ø bit.
Use the parts 011053, 008004 and 001004 (Fig. 1).
24. Position the first baluster 127031 or 127035; adjust the height in relation to the balusters fitted previously (Fig. 1).
25. P repare the helical handrails 140051, the parts 031073, 002026 and the plastic spacers 031077; the latter
are made of a soft transparent material, be careful not to confuse them with the parts 031076 made of a rigid
transparent material, which are exclusively to be used for the joints of straight handrails (Fig. 1).
26. C ut 5 cm off the starting handrail and fasten the part 033164, using the parts 011069 and 004034, drill a
hole using a 6 mm Ø bit. Start assembling the handrails on the balusters with the parts 002031 starting from
the bottom. Continue with assembling the handrails fitting the joining parts 031073, 031077 and the retaining
screws 002026. Check that the balusters are vertical and turn the handrail sections so that they are perfectly
linear (Fig. 1).
27. In correspondence to the last baluster, orthogonally cut off the excess handrail using a wood saw (Fig. 1).
28. C omplete the handrail by fitting the part 033164, using the parts 011069 and 004034, drill a hole using a
6 mm Ø bit (Fig. 1).
8 - REX T
