Worx WG169E Manual De Instrucciones página 14

or edging.
WARNING! Only use 1.65mm
diameter cutting line. Other sizes of
line will not feed properly and will result
in improper cutting head function or can
cause serious injury. Do not use other
material such as wire, string, rope, etc.
Wire can break off during cutting and
become a dangerous projectile that can
cause serious injury.
EDGE /TRIMMING SUPPORT WHEELS
There are three optional positions for the Edge
/Trimming Support Wheels to attach when
assisting in Trimming and Edging.
Position 1: Using the guide wheels when
trimming in a forward or reverse direction
(See Fig. J1)
Position the Grass Trimmer in the trimming
position. Underneath the Safety Guard there is
a metal plate that the Edge/Trimming Support
Wheels will attach to. Slide the Support
Wheels horizontally onto the metal plate until
they lock into position so both the wheels are
facing in the forward direction (See Fig. B3).
14
The wheels should provide support when
you are trimming in the forward or reverse
direction.
Position 2: Using the guide wheels when
trimming Side to Side
Position the Grass Trimmer in the trimming
position. Underneath the Safety Guard there
is a metal plate that the Edge/Trimming
Support Wheels will attach to. Slide the
Support Wheels vertically onto the metal plate
until it locks into position (See Fig. B2). The
wheels should provide support when you are
trimming in a horizontal side to side direction
(See Fig. J2).
NOTE: you could also use the machine
without the guide wheels on guard when
trimming.
Position 3: Using the guide wheels when
edging (See Fig. I2)
WARNING: Make Sure the Safety
Switch is Locked Off to Prevent
Accidental Starting.
Change the tool from trimming into the
edging mode, the Edge /Trimming Support
Wheels (12) will attach on the side the trimmer
3-in-1 Grass Trimmer/Edger
head as shown in Fig. B1.; rotate the main
handle as described in ''MAIN HANDLE
ROTATION'', then unlock the Pivot Head
Locking Knob, and using adequate force, pull
the trimmer head into the desired position.
Make sure to adjust the trimmer head angle
to be in the lowest horizontal setting. Finally,
lock the Pivot Head Locking Knob (See Fig. H3)
and position the wheels on the ground for the
edging mode. While edging, keep the Flower
Guard/Edge Guide aligned with the sidewalk
edge, this will assist to edge in a straight path.
Only the tip of the line will make contact with
area being worked on. Do not force the line.
The edging wheels help protect the unit and
keep the unit from contacting the ground. Take
extra caution while edging, as objects can be
thrown from the trimmer line.
AUTOMATIC LINE FEED SYSTEM
When initially switching on the trimmer, a
small length of line is fed out. Each time the
tool is started from rest it will advance about
6.35mm of trimmer line.
A 'clattering' noise will be heard when the
lines hit the Line Cutter. DO NOT BE ALARMED
this is quite normal. After about 5 seconds
the line will be cut to the correct length and
the noise will reduce as the motor gains full
speed.
If the noise of the line being cut can't be
heard, more line will need to be fed out.
To feed more line, it is first necessary to allow
the trimmer to stop completely; it must come
to a complete rest, then restart, allowing the
motor to reach full speed.
Repeat above until you hear the line hitting
against the Line Cutter.
TO MANUALLY FEED THE LINE
(See Fig. K1)
Turn off the trimmer and remove the battery.
If required, line can be fed out manually.
To operate, press and release manual Line
Feed Button (17), while gently pulling out the
line until it is long enough to reach the Line
Cutter.
If the line extends past the Line Cutter, too
much line has been fed out.
If too much line is fed out, remove the Spool
EN