3M PELTOR ComTac VI NIB Manual Del Usuario página 10

6
3
2
5
1
4
8
9
7
Which NIB group you belong to depends on where you and the
other NIB headsets are located.
NIB operates when the environmental noise level exceeds
approx. 80 dB and when the noise is continous for approx.
1 second.
NIB also operates in less than 80 dB if the user presses the
PTT in either PTT mode or VOX mode.
Activating NIB (Fig 7)
Quickly double pressing the PTT will toggle between NIB PTT
ON/NIB OFF/NIB VOX ON.
Pressing and holding the NIB PTT button allows for
communications within the 10 m radius when in NIB VOX ON
mode and NIB PTT ON mode.
NIB VOX ON - In this mode, high levels of noise will activate
the NIB radio and allow VOX communications for up to four
users. Pressing the PTT button in VOX ON mode also allows for
communication in quiet.
When the headset operates in an environment with intermittent
noise, noise can activate NIB VOX repeatedly. In this situation,
you can use NIB PTT ON.
NIB PTT ON - In this mode, the PTT button must be pressed to
transmit.
NIB OFF - this mode TURNS OFF the NIB radio. In NIB OFF,
no RF signal is being emitted from the NIB radio.
Push-to-talk for NIB (Fig 8)
Press and hold the PTT on the left cup to transmit on the NIB.
Entering the menu (Fig 4)
1. Press and hold the [+] and [–] button to enter the menu.
A voice will confirm.
2. Press the [–] button briefly to toggle through the menu. The
menu steps are listed below.
3. Use the [+] button to change the setting and, if available,
toggle through the available settings. A voice message confirms
each step, followed by the current setting. Changes are also
confirmed by a voice message. After a few seconds of no
activity, the menu returns to volume mode. By pressing [+] and
[–], the volume setting can be instantly reached at any stage of
the menu.
6
5
3
2
1
4
8
9
7
4
Ambient/Environmental listening mode
The ambient/environmental listening mode is available in classic
mode and advanced mode. Classic mode allows you to adjust
the volume in four steps by increasing or decreasing the sound
level of the ambient/environmental listening. Advanced mode
includes four preset settings optimized for different sound
profiles.
Setting
Advanced mode 1 For comfort in a very noisy environment.
(Comfort)
Advanced mode 2 For a natural audio experience where protection
(Conversation) against sudden noises is necessary.
Advanced mode 3 For high situational awareness when walking in
(Patrolling) a low noise environment.
Advanced mode 4 For powerful situational awareness in a quiet
(Overwatch) environment.
Battery
Choose the type of battery you are using in your headset,
alkaline or rechargeable.
Wireless input
1. Follow the user instruction for the 3M™ PELTOR™
TEPLOOP-* to set up the neckloop.
2. Enter the headset menu to adjust the wireless input and the
sensitivity to correspond to the connected neckloop. Choose
Off/Low/Medium/High.
3. Adjust the volume on the external radio if needed.
NOTE: The volume may differ depending on the distance
between the headset and the neckloop
Wired Input
Adjust the wired input and sensitivity to correspond to the wired
device. Choose Low/High.
Balance
The balance setting adjusts the volume balance between the
right and the left ear. There are seven level settings: Center,
Left 1, Left 2, Max left, Max right, Right 2, Right 1.
Warning signals
The warning signal setting disables/enables the warning signals
"low battery" and "automatic power off". When switched off,
none of these warning signals will be heard.
Automatic power off
The automatic power off setting disables/enables the automatic
power off function.
NIB frequency
For North America, Australia and New Zealand, the frequency
for NIB is 915 MHz.
For Europe the frequency for NIB is 864 MHz.
Choose the NIB frequency, 864 MHz (EU) or 915 MHz (NA,
EN
Intended use