Cub Cadet L20 Manual Del Usuario página 18

Ocultar thumbs Ver también para L20:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 108
EN
Adjusting the cutting height J
To set the cutting height, press the cutting height
Î
adjustment lever [1].
Note
"4" is the largest possible cutting height
(approx. 10 cm); the cutting mechanism is
located right at the top.
"Lo/1" is the smallest cutting height (ap-
prox. 2.5 cm); the cutting mechanism is
located right at the bottom.
Depending on the model, the control panel
is equipped with an adjustable position
indicator [2]. This helps you find the required
cutting height more quickly.
Mowing
Items flung out (cut grass, stones, etc.)
ÂRisk of injury
¾ Only empty the grass catcher when the
cutters are switched off.
¾ Only operate the device with the grass
catcher attached or an optional deflector.
Attention!
¾ If a foreign object (like a stone) comes into
contact with the cutting mechanism, or if the
device starts to vibrate unusually, switch the
engine off immediately.
¾ Inspect the device for damage before continuing
operation. In the event of damage, discontinue
use of the device and have it repaired by
a service centre prior to putting back into
operation.
¾ Do not activate the cutter deck in high grass.
Start the engine as indicated.
Î
Set the throttle to
Î
Switch the cutter deck on and then lower it.
Î
Release the parking brake by pushing right
Î
through the brake pedal and then releasing it
again.
To drive off, press on the accelerator pedal.
Î
Notes on mowing
Do not mow wet grass. Drive slowly at maxi-
mum engine speed.
Mowing on tall or wet grass may lead to
uneven grass accumulation / blockages in
the discharge chute.
18
CAUTION!
.
Notes on mowing
Depending on the model, the device may
have a fill level indicator for the grass
catcher. The fill level sensor Y measures
the extent to which the grass catcher is filled
during mowing. When the grass catcher is
full, an acoustic signal sounds and, depend-
ing on the model, the cutting mechanism
automatically, simultaneously switches itself.
The grass catcher must then be emptied
prior to further mowing. The sound signal is
only deactivated after emptying the grass
catcher.
Setting the fill level sensor
(model-dependent) Yb
Risk of injury
¾ Only make adjustments to the fill level
sensor when the engine is switched
off, the parking brake is engaged, the
ignition key is removed and the grass
catcher has been detached.
Note
This kind of setting is only possible on
devices equipped with an adjustable fill level
sensor.
The measuring angle of the fill level sensor can
be changed (multiple locking positions) and thus
matched to the consistency of the grass cuttings.
In this process, the degree of filling of the grass
catcher is influenced at the same time.
To reduce the measuring angle, undo the knurled
Î
screw of the fill level indicator 1 .
Move the adjustable part of the fill level sensor
Î
forwards in the direction of the rear panel into the
desired position 2 .
Re-tighten the knurled screw 3 .
Î
3 The sound signal is triggered later; the cutting
mechanism is deactivated later, depending on the
model.
Note
Ideal for short, very dry grass cuttings.
To increase the measuring angle, undo the
Î
knurled screw of the fill level indicator 1 .
Move the adjustable part of the fill level sensor
Î
towards the rear into the desired position 2 .
Re-tighten the knurled screw 3 .
Î
3 The sound signal is triggered earlier; the cutting
mechanism is deactivated earlier, depending on
the model.
3
Note
Ideal for lush, damp grass.
WARNING!
Operation
Tabla de contenido
loading

Este manual también es adecuado para:

769-11724fXz3Xt3qr95

Tabla de contenido