Technical Data; Jig Saw Safety Warnings; Specified Conditions Of Use - BTI A18 ST-S Manual Original

TECHNICAL DATA

Code ................................................................................................................
Battery voltage.................................................................................................
Stroke rate under no-load
1st gear ........................................................................................................
2nd gear .......................................................................................................
Lengths of stroke .............................................................................................
Bevel cuts up to ...............................................................................................
Cutting depth max. in:
Wood ...............................................................................................................
Steel ................................................................................................................
Aluminium .......................................................................................................
Weight according EPTA-Procedure 01/2003 (1.5/2.0 Ah) ..............................
Weight according EPTA-Procedure 01/2003 (3.0/4,0/5.0 Ah) .........................
Weight according EPTA-Procedure 01/2003 (9.0 Ah) .....................................
Noise information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ................................................
Sound power level (Uncertainty K=3dB(A)) .....................................................
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to
EN 60745
Sawing of wood
Vibration emission value a ..........................................................................
h
Uncertainty K= .............................................................................................
Sawing of sheet metal
Vibration emission value a ..........................................................................
h
Uncertainty K= .............................................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to
compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent
accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually
doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep the hands warm,
organisation of work patterns.
WARNING! Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric shock, fi re and/or
serious injury.
Save all warnings and instructions for future reference.

JIG SAW SAFETY WARNINGS

Wear ear protectors. Exposure to noise can cause hearing loss.
Hold power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring.
Cutting accessory contacting a „live" wire may make exposed metal parts
of the power tool „live" and could give the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with
the machine. The use of protective clothing is recommended, such as dust
mask, protective gloves, sturdy non-slip footwear, helmet and ear
defenders.
The dust produced when using this tool may be harmful to health. Do not
inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch
the device on again while the insertion tool is stalled, as doing so could
trigger a sudden recoil with a high reactive force. Determine why the
insertion tool stalled and rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is running.
ENGLISH
445 603 - BTI-A18ST-S.indd 22 445 603 - BTI-A18ST-S.indd 22
CORDLESS JIGSAW
A18ST-S 02 00001- 99999
...................................18 V
...............................2050 min
...............................2700 min
...................................26 mm
................................. 45°
.................................120 mm
...................................10 mm
...................................30 mm
..................................2,8 kg
..................................3,1 kg
..................................3,5 kg
................................82,5 dB (A)
................................93,5 dB (A)
..................................6,3 m/s
..................................1,5 m/s
..................................6,4 m/s
..................................1,5 m/s
When working in walls ceiling, or fl oor, take care to avoid electric cables
and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can
cause severe injury and damage.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft materials
(wood, light building materials for walls). Harder materials (metals) must
fi rst be drilled with a hole corresponding to the size of the saw blade.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning
them. BTI off er to retrieve old batteries to protect our environment; please
ask your sales representative or our service line at 07940 / 141-141.
Do not store the battery pack together with metal objects (short circuit risk).
No metal parts must be allowed to enter the battery section of the charger
(short circuit risk).
Use only System 18 V chargers for charging System 18 V battery packs.
Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms.
Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load or
extreme temperatures. In case of contact with battery acid wash it off
immediately with soap and water. In case of eye contact rinse thoroughly
for at least 10 minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product damage
due to a short circuit, never immerse your tool, battery pack or charger in
fl uid or al-low a fl uid to fl ow inside them. Corrosive or conductive fl uids,
such as seawater, certain industrial chemicals, and bleach or bleach
containing products, etc., Can cause a short circuit.

SPECIFIED CONDITIONS OF USE

This jig saw can cut wood, plastic and metal; it can cut straight lines,
bevels, curves, and internal cut-outs.
Do not use this product in any other way as stated for normal use.
22
A18ST-S
-1
-1
2
2
2
2
31.01.2018 12:23:11 31.01.2018 12:23:11