Safety Instructions; General Working Stand Safety Warnings - Flex SBG 4910 Instrucciones De Funcionamiento Originales

SBG 4910

Safety instructions

t^okfkd>
 Keep children away from the power tool.
 If the power cord is damaged while
the power tool is being used, do not touch
the power cord. Immediately pull out
the mains plug. Never use a power tool
which has a defective power cord.
 Repairs such as replacing a damaged
cord, may be carried out by an authorised
customer service centre only.
 Before performing any work on the power
tool, pull out the mains plug.
 Always lay the power cord to the rear away
from the machine and keep away from
the work area.
 When using the power tool, wear
protective equipment:
close-fitting clothing, goggles,
ear protection, protective gloves.
If required, also wear a hair net!
 Never cut a workpiece held in your hand.
Always clamp the workpiece securely
in the vice.
 Remove cut-offs and swarf from the work
area. The machine must be switched off!
 Before use, check machine and saw band
for damage.
 Use sharp, faultless saw bands only.
Immediately replace blunt or defective
saw bands.
 Keep hands away from the work area
while the machine is running.
 Switch on saw band before guiding
towards the workpiece.
 If the saw band is blocked, switch
off the machine immediately.
Wait until the power tool comes
to a standstill before pulling it out
of the workpiece.
 Do not load the power tool to such an
extent that it stops.
 If power tools are used outdoors, connect
via a residual-current-operated circuit-
breaker (tripping current max. 30 mA).
a^j^db=ql=molmboqv>
 The mains voltage and the voltage
specifications on the rating plate (5) must
correspond.
 Do not use lubricants or coolants.
General working stand safety
warnings
t^okfkd>
oÉ~Ç=~ää=ë~ÑÉíó=ï~êåáåÖë=~åÇ=~ää=áåëíêìÅíáçåë=
éêçîáÇÉÇ=ïáíÜ=íÜÉ=ïçêâáåÖ=ëí~åÇ=~åÇ=íÜÉ=
éçïÉê=íççä=íç=ÄÉ=ãçìåíÉÇK=c~áäìêÉ=íç=Ñçääçï=
íÜÉ=ï~êåáåÖë=~åÇ=áåëíêìÅíáçåë=ã~ó=êÉëìäí=áå=
ÉäÉÅíêáÅ=ëÜçÅâI=ÑáêÉ=~åÇLçê=ëÉêáçìë=áåàìêóK
 Save all warnings and instructions for
future reference.
 Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjustments
or changing accessories.
Accidental starting of the power tool
is a cause of some accidents.
 Properly assemble the working stand
before mounting the tool. Proper assembly
is important to prevent risk of collapse.
 Securely fasten the power tool to the
working stand before use. Power tool
shifting on the working stand can cause
loss of control.
 Place the working stand on a solid, flat and
level surface. When the working stand can
shift or rock, the power tool or workpiece
cannot be steadily and safely controlled.
 Do not overload the working stand or use
as ladder or scaffolding. Overloading or
standing on the working stand causes the
stand to be "top-heavy" and likely to tip
over.
 Do not install or use an other power tool to
the working stand.
15