Care And Maintenance - Waterpik Sonic-Fusion SF-01 Manual De Instrucciones

8

CARE AND MAINTENANCE

Travel and Hose-Free Brushing
Toothbrush can be disconnected from the Sonic-Fusion® for travel or hose-free
brushing. Place the handle and desired brush head(s) in the provided case for
protection when traveling.
NOTE: To disconnect the toothbrush from the water hose, press the round button
on the back side of the power handle.
Using Mouthwash and Other Solutions
Your Waterpik® Sonic-Fusion® can be used to deliver mouthwash and antibacterial
solutions. After using any special solution, rinse unit to prevent clogging by partially
filling reservoir with warm water and running unit with brush head pointed into sink.
Care and Maintenance
Before cleaning, unplug from the electrical outlet.
After Each Use
1. After each use, when all functions are turned OFF, remove the brush head
from the handle and rinse brush head under running water.
2. Wipe the handle dry after each use.
Brush
Floss
General Cleaning / Removing Hard Water Deposits
• Clean the product when necessary by using a soft cloth and mild
non-abrasive cleanser.
• Hard water deposits may build up in your unit, depending on the mineral
content of your water. If left unattended, it can hinder performance. Cleaning
internal parts: add 2 tablespoons of white vinegar to a full reservoir of warm
water. Point the handle and brush head into sink. Turn Water Flosser ON and
run until reservoir is empty. Rinse by repeating with a full reservoir of clean
warm water. This process should be done every 1 to 3 months to ensure optimal
performance.
Toothbrush Low Charge Lock Out
The toothbrush charge indicator lights will flash if the battery charge is too low for
brushing. This may cause the toothbrush to enter Lock Out mode. To clear the Lock
Out, place the power handle on the charging base.
Leakage
If leaking due to a damaged hose, replacement hoses can be purchased at
www.waterpik.com or contact Water Pik Inc. customer service for a self service
repair kit.
Multiple Unit Proximity
To avoid wireless communication interference when more than one unit will be used
in proximity, go to (waterpik.com/MUP) for instruction for changing the base and
handle ID.
Battery Removal
This product contains rechargeable Nickle Metal Hydride batteries. The batteries
are not replaceable. Please do not dispose of the unit in the household waste.
Remove the batteries per the instructions below and recycle at your local recycling
center.
Note: This process is not reversible
Remove the battery only at the end of the product's life for recycling. Doing so
earlier will destroy the product. Deplete the battery charge until the brush no longer
operates. Observe basic safety precautions to protect your eyes, hands, fingers, and
work surface. Remove the batteries as shown and recycle them and the rest of the
product according to local regulations.
1. Run down the battery by operating the brush button until the motor
does not run.
2. Obtain a towel or cloth, hammer, flat-head screwdriver, and wire cutters.
3. Remove and discard the brush head.
4. Cover the handle entirely with the towel or cloth.
5. Clamp the top of the handle against your work surface with one hand and
strike the handle housing around the bottom perimeter on all sides to release
the end cap latch. Continue striking and rotating the handle until the end
Remove
cap releases.
Battery
6. Remove the internal components by turning the handle upside down and while
holding on to the handle housing, press the shaft down firmly on a hard surface.
7. The internal components should slide out when the handle is positioned
upside-down. If this does not occur, repeat steps 5 and 6 until the
Cut
components release.
8. Remove the end cap from the internal assembly.
9. Slide the battery out of the internal assembly.
10. Cut the battery wires one at a time with the wire cutters.
11. Recycle and dispose of the battery properly.
12. The remaining product pieces should be discarded appropriately.
9