Putting Into Operation; Spare Parts; Outer Cleaning - IARP FRESH 42 Instrucciones De Uso

Model - Modello - Modèle
Modell - Modelo
Constructeur - Fabbricante
Manufacturer - Hersteller
Fabricante

23. PUTTING INTO OPERATION

If the cabinet has been sharply tilted while being sited or for mounting of accessories, it must be left to stand for
at least three hours before being started to allow the lubricating oil to settle in the compressor.
Failure to do so can cause total destruction of the compressor refrigerating system.
Check that the voltage on the identification plate is the same as that of the network.
THE ELECTRICAL SUPPLY LINE TO WHICH THE REFRIGERATOR WILL HAVE TO
BE CONNECTED IS TO BE PROTECTED BY A VERY SENSITIVE DIFFERENTIAL
SWITCH (Rc=16A,Dc=30mA); IT IS ALSO TO BE LINKED TO THE
GENERAL EARTHING PLANT.
Earthing is necessary and compulsory by law.
Absolutely never use reduction units, patch cords, adapters or multiple socket
outlets to connect the counter. DIRECTLY connect the equipment to the mains.
The cable should be fully extended and located where it is unilikely to be struck, caught or stepped on,
away from water and the other liquids and heat sources and must not be damaged. In case of breakage of the power
cable of the cabinet, it must be replaced by the manufacturer or by instruction it change of it.
Follow the manufacturer's instructions to install the unit, using qualified personnel and complying with the electrical
regulations for the specific country. Incorrect installation may cause injury and damage; the manufacturer is not liable
The manufacturer disclaims all responsability for any damage to people or things
for this.
due to incorrect observance of this rule.
24. INSTRUCTIONS FOR CORRECT INSTALLATION AND
MAINTENANCE
The user and maintenance instructions are found in the User Manual available on the website www.eptarefrigeration.com.
The installation instructions dedicated to expert personnel are available:
• From the service network
• In some product categories in paper form delivered with the product.
25. PROFESSIONAL REPAIR SERVICES
The services are provided by our service network that can be consulted in the contact area at the web address: www.eptarefrigeration.
com.

26. SPARE PARTS

The spare parts and the information to repair the unit are available for at least 8 years after the product is declared out of production
at the following web address: www.epta-service.com/service/.
The credentials are provided on request by sending an email to: [email protected]

27. OUTER CLEANING

WARNING! TURN OFF POWER SUPPLY TO THE CABINET BY DISCONNECTING THE POWER
PLUG BEFORE CLEANING.
For a good preservation of the cabinet's body a periodical cleaning is necessary.
1. EXTERNAL BODY:
When necessary, the external body should be cleaned with a cloth and a neutral soap and water solution.
2. STAINLESS STEEL SURFACES:
pads etc. which will spoil the finish of the stainless steel.
3. SURFACES IN PLASTIC MATERIAL:
no circumstances should alcohol, methylated spirits or solvents be used.
4. GLASS SURFACES:
can leave a film of calcium on the surface of the glass.
WARNING! Do not use jet of water to clean the cabinet: electrical wiring could be damaged.
WARNING! Never use mechanical devices or any other means to accelerate the defrosting process,
other than those recommended by the manufacturer.
FRESH 42
EPTA S.p.A. - Sede legale
Via Mecenate, 86 - 20138 Milano – Italy
Capitale € 68.515.000 - R.E.A./MI – 1730229
Registro delle Imprese e Cod.Fiscale n. 04160730968
Partita IVA 04160730968
Wash with warm water and mild detergent, rinse well and dry with soft cloth. Avoid scouring
Wash with warm water and mild detergent, rinse well and dry with soft cloth; under
Only use products specifically designed for glass cleaning; It is not advisable to use ordinary water which
1 9 / 5 6
PAGE
N° DOC