Technical Specification; User Instructions - 3M Speedglas G5-01 Instrucciones De Uso

Ocultar thumbs Ver también para Speedglas G5-01:

Instrucciones de uso (77 páginas)

Contenido

página de 62

/ 62
Contenido
Tabla de contenido

Tabla de contenido

GZXO

Please read these user instructions in conjunction with other

relevant user instructions and reference leaflets where you

will find information on approved combinations, spare parts

and accessories

SYSTEM DESCRIPTION

The 3M™ Speedglas™ Task light G5-01 is designed to be

used only with the Speedglas welding helmet G5-01. The

Speedglas task light G5-01, powered by a 3M™ Adflo™

Li-ion Battery, enables welders to light up the work area in

order to get a better view of the workpiece.

^ WARNING

Proper selection, training and appropriate maintenance is

essential in order to ensure correct usage of the product. For

suitability and proper use follow local regulations and refer to

all information supplied.

^ Particular attention should be given to warning

statements where indicated.

^ Only use with original 3M spare parts and accessories

listed in the reference leaflet and within the usage conditions

given in the Technical Specifications.

^ The use of decals, paint or other modifications not

specified in these user instructions may invalidate claims

under the warranty or cause the product to be noncompliant

with approvals.

^ Possibly hazardous optical radiation emitted from this

product. Do not stare at the operating lamp. May be harmful

to the eye.

^ When removing/uninstalling the task light assembly, there

is a potential for light leakage through the installation holes. A

new lamp or a new solid neck protection needs to be fitted.

APPROVALS

The product is CE marked and in conformity with the

European directives as listed in fig 8. The Declaration of

Conformity is available at www.3m.com/Welding/certs.

EQUIPMENT MARKING

Z = Read the instructions before use

= Optical radiation - risk group 2

= Manufacturing year

= Manufacturing month

= Shall be disposed of as electrical and

electronic waste

Additional markings on the product refer to other standards.

PREPARATION FOR USE

Carefully check that the product is complete (see fig 1),

undamaged and correctly assembled, any damaged or

defective parts must be replaced before each use.

• Mounting of cable in helmet fig. 2A-2B

• Mounting of lamp fig. 3A-3C

• Mounting of cable on breathing tube fig. 4A-4B

• Mounting of cable in 3M™ Adflo™ Battery fig. 5A-5B

OPERATING INSTRUCTIONS

• ON/OFF: press the power button shortly, fig 6. When

activated, the lamp will have the same light intensity as it had

when the lamp was last used.

• Light intensity: Max, High, Medium, Low.

• Change of light intensity: hold the power button down in

order to rotate between the four light intensity levels, fig 6.

• Power saving: The light intensity is automatically reduced as

the battery charge decreases. When the battery charge is low

the lamp will switch to low light intensity and flash twice in

order to alert the user.

• It is not possible to change light intensity when the battery

charge is low, this will be indicated by the light flashing twice.

• The lamp cannot be switched on if the battery charge is

empty.

• When the battery is empty the lamp automatically turns off.

• Thermal protection: If the lamp gets too hot and to protect

the LEDs from overheating, the light intensity automatically

decreases. When the temperature recovers it will

automatically increase the light intensity.

• If the lamp is overheated it will flash four times and

automatically turn off.

• Always turn off the lamp after use.

CLEANING INSTRUCTIONS

Clean the task light and protection plate with a lint-free tissue

or cloth.

To avoid damage to the product do not immerse in water or

spray directly with liquids.

MAINTENANCE

• Replacement of outer protection plate, fig. 7A-7B

^ The product should be disposed of according to local

regulations.