Ferguson Enterprises ProFlo PF5511 Instrucciones Para La Instalación

Installation Instructions
Shroud for
Wall Hung Lavatories
PF5511/5514/5518
Tools Needed
A. Screwdriver
B. Wrench
C. Tape Measure
D. Level
E. Drill
F. Marker
Caution: Product is Fragile!
To avoid breakage and possible
injury, handle with care!
Installation Procedures
1. For ADA installation, determine the sink
position on the wall using the reference guide in
Table 1. (NOTE: Remember that when you reduce
the height of the hanger for "Children Environment"
installation, the same adjustment must be made to
lower the water supply and drain.)
TAS
ADA
"Childrens
ADA/TAS "Childrens
Environment
Environment"
Ages K-5 yrs"
A 34" (86.4 cm) 31" (78.7 cm) 30" (76.2 cm) 32" (81.3 cm)
B 27" (68.6 cm) 24" (61 cm) 26" (66 cm)
C 11" (27.9 cm) 11" (27.9 cm) 11" (27.9 cm) 11" (27.9 cm)
D 9" (22.9 cm) 9" (22.9 cm) 9" (22.9 cm)
E 8" (20.3 cm) 8" (20.3 cm) 8" (20.3 cm)
F 34" (86.4 cm) 31" (78.7 cm) 30" (76.2 cm) 32" (81.3 cm)
2. If this is a new installation and there is no
support, remove any drywall and mortise 2"x
6" boards for suitable reinforcement behind the
finished wall as shown in Figure 1. Re-finish the
dry wall and paint as desired.
2 x 6 support
Lavatory
Hanger
Shroud
support Supply
clips
Waste
Figure 1
Distributed exclusively by Wolseley North American Division: Ferguson, Stock Building Supply and Wolseley Canada.
© 2013 Ferguson Enterprises, Inc. All Rights Reserved.
3. Placement of the hanger bracket support is
determined by measuring from the center line
of the hanger to the floor, F in Figure 2 of the
appropriate model.
C/L
Wall Bracket
TAS
"Childrens
Environment 4. Mark the hanger bracket height and mounting
Ages 6-9 yrs"
holes locations, pre-drill the holes at the marked
location and secure the hanger with four (4) 5/16"
28" (71.1 cm)
lag bolts.
9" (22.9 cm)
8" (20.3 cm)
CL
Hanger
Bracket
Figure 3
5. Please note the location of the water supply
and drain as shown in Figure 3 & Figure 4 of your
specific model. There are optional locations for
the supply depending on your desire to have it
concealed under the shroud or not concealed.
6. Mark the location of the shroud support clips
(provided) as shown in Figure 4 of your specific
model. Pre-drill the holes at the marked location
and loosely attach the clips with three (3) 1/4" lag
bolts.
Figure 2
CL
Lavatory
Hanger
Bracket
CL
Shroud
Attachment
Clips
7. Lift the lavatory on top of the hanger support
bracket by placing the rear lip of the lavatory on the
hanger support bracket. Make sure the rear lip is
securely engaged and centered on the hanger.
Check that the lavatory is level. Figure 5
Finished Floor
8"(205mm)
6-1/4"(159mm)
2-3/4"
3/8 " Hot
3/8 " Cold
(70mm)
Optional
Optional 3/8 " Cold
3/8 " Hot
1-1/2"
4 "(102mm)
(38mm)
1-1/4 " OD
Figure 4
10-1/2"(267mm)
Figure 5
16362 0713