On/Off Switching - Trevi AVX 590 BT Manual Para El Uso Y La Conexión

ENGLISH
REMOTE CONTROL BATTERY ACTIVATION AND REPLACEMENT
The remote control works with two type "AAA" batteries (not supplied) to be inserted in the battery compartment on the back.
When inserting the batteries, observe the polarity 'marks in the battery compartment.
INSTALLATION AND CONNECTION
Connect the satellite speaker cable jack (the one without controls) to the SPEAKER connector (7).
CONNECTING TO THE POWER SUPPLY
Fit the plug into an 230V ~ 50Hz socket. Do not plug the appliance to different power.

ON/OFF SWITCHING

1. Press the main ON/OFF switch (8).
2. Press the main ON/OFF switch again to switch the appliance off.
STANDBY
1. With the ON/OFF switch (8) set to ON, press down on the knob (2) or press the Power-on/standby key (11) on the remote control to activate the
appliance.
2. Hold for a few seconds, the knob (2) or press the Power-on/standby key (11) again to switch the appliance back to standby mode.
VOLUME CONTROL AND MUTE FUNCTION
Volume can be adjusted unit, by unit, turning the knob (2) or by remote control using the volume control keys (volume up 19) (volume down 17).
During the adjustment the LED indicator (3) will flash.
MUTE function: it is possible to activate the audio off function with the MUTE key (18); the indicator LED (3) flash to indicate activation of the function.
To switch the audio on, press the MUTE key (18) again.
TREBLE, BASS AND PRE-EQ CONTROL
Is possible to make an adjustment of the high and low tones during the playback:
1. Treble: Press TREBLE + button (21) or TREBLE- (15) to make the adjustment.
2. Bass: Press BASS + button (20) or BASS- (16) to make the adjustment.
3. Status LED indications (3) when adjusting: pink flashing indicates adjustment in progress, pink fixed end adjustment layer.
Four different types of sound equalization with which to listen to the music tracks are also available:
1. Press one of the four keys (23) corresponding to the pre-equalization to be activated.
Hold for a few seconds the RESET button (13) the set tone and equalization are reported to the initial value (default value).
USB PLAYER OPERATION
Note: The unit may not support some USB devices, this is due to the incompatibility of some processors.
PLAYBACK
1. Insert an USB device in the USB port (4).
2. Switch On the appliance and press the knob (2) several times or press several times the INPUT key (12) until the indicator LED (3) will show the
pink color.
3. After a few seconds the player will automatically start playing the detected audio tracks (MP3).
4. Press the key (22) to pause the playback.
5. To disable the pause press the  key (22) again.
6. Status LED indications (3) during playback: Pink color indicates current playback, pink flashing indicates paused playback.
TRACK SKIP
1. While listening, press the  key (22) to move to the next track; press the  key (22) to move to the previous track.
AUX-IN 1/AUX IN 2 INPUT
1. Connect any type of appliance featuring an audio output to the AUX IN 1 input (9) or to the AUX IN 2 input (10) using a 3.5 mm jack plug cable.
2. Switch ON the appliance and press the knob (2) several times or press several time the INPUT key (12) until the indicator LED (3) will show the
Green color (AUX IN 1) or Light Green color (AUX IN 2).
3. Control the external unit with its controls.
COAXIAL DIGITAL AUDIO INPUT
1. TO Use a coaxial cable to connect the COAXIAL (5) input to the coaxial digital output of the TV or other source device.
Coaxial Audio Input
Coaxial Cable
Coaxial Audio output
8
AVX 590 BT