Idiomas disponibles
Idiomas disponibles
(C67). Use components C58, B12, B83 and B02 (fig. 1).
25. Identify the handrail sections not marked with the colour red (A13), and those marked with the colour red (A14),
which will be used for the landing (E02) (fig. 9).
26. Start to shape the handrails (A13) which are not marked with the colour red, trying to give them a curvature
which follows as closely as possible that of the staircase (fig. 1).
27. Starting from the baluster (C67) from the landing (E02), begin to fix the handrail (A13) which you have just
shaped. Use the C64 components, with the screwdriver. Warning: position the handrail so that the joining line of
the surface covering is facing downwards.
28. Unite the other handrail segments (A13), screwing them, gluing them (glue X01) and shaping them in
succession. Use components B33 and D72.
29. Cut the excess handrail with a hack-saw so that it corresponds with the first baluster (C67) on the staircase.
30. Complete the handrail (A13), fixing component A12 using components C64 and the glue (X01) (fig. 1).
31. Insert the steel cables F30 into the items C69 present on the balusters. Lock the cables onto one of the two
ends with items D37 and C76, leaving 5 mm of the cable protruding from item D37.Tighten the cables by
hand and lock them with items D37 and C76. Cut off the cable at a distance of 5 mm from item D37. Screw
on components D36, which protect users from the cables. Warning: to cut the cables, we suggest that you
use suitable shears, and that you wrap adhesive tape around the part of the cable to be cut so that it will not
unravel.
32. Check the line of the handrail (A13) and, if necessary, correct it by using a rubber hammer.
33. Complete the assembly of the handrail, inserting components C78 into the side part of the treads (fig. 1).
Assembling the balustrade
34. Position components F34, using items C58, B83, B02, on the landing (E02). Drill a hole in the landing (E02)
using a Ø 5 mm bit and maintaining a distance between the holes which is similar to that between the balusters
(C67) of the banister which you previously assembled.
35. Assemble column (C73) onto component G01, which protrudes from the landing (E02), orientating items C69
outwards, using components D49 (fig. 8) (fig. 1).
36. Position the shortest balusters (C68) and tighten items B02 onto components F34 (fig. 1).
37. Fix item A15 to the handrail A14 with the glue (X01) and attach component A15 to the column (C73) using item
B02 (fig. 1).
38. Fix the handrail (A14) marked in red, using items C64 (fig. 1). Cut off the excess handrail using a metal saw and
complete the handrail (A14) by fixing item A12, using items C64 and the glue X01.
39. Insert the steel cables F30 into the items C69 present on the balusters. Lock the cables onto one of the two
ends with items D37 and C76, leaving 5mm of the cable protruding from item D37. Tighten the cables by
hand and lock them with items D37 and C76. Cut off the cable at a distance of 5 mm from item D37. Screw
on components D36, which protect users from the cables. Warning: to cut the cables, we suggest that you
use suitable shears, and that you wrap adhesive tape around the part of the cable to be cut so that it will not
unravel.
40. According to the position and the existence of walls around the stair-well, it may be necessary to position one or
two extra balusters (C68) (fig. 10).
41. In this case it is necessary to consider a space which would be equidistant from the other balusters or from the
walls. To fix them, we recommend drilling a hole in the (E02) landing with a Ø 5 mm bit and using components
F34, C58, B83 and B02, while the floor will need holes drilled with a Ø 14 mm bit and uses components F34,
B02 and B13 (fig. 11). If it is necessary to join the landing banister to the floor banister (fig. 10), shape the
handrails carefully, forming curves which match up. If wrinkles should form on the inside of the handrails, it is
not a defect. Rub them energetically (generating heat) with a paper tissue until they go away.
Final Assembly
42. To further strengthen the staircase at intermediate points, fix the components F09 to the wall, and join them to
the balusters (C68) using components F33. Drill the holes with an Ø 8 mm bit and use components C50, C49,
C58, and B12 (fig. 12).
www.fontanot.it
9 - ko
