Idiomas disponibles
Idiomas disponibles
CONTROL PANEL NE276M
GB
CONTROLS:
Push button for turning
INTERNAL LIGHTS on or off
Push button for turning
EXTERNAL LIGHTS on or off
(*) the indication of the active load is also appears on the display with the symbol.
SCREENS:
In the main screen always displays the date, time
internal temperature. Also displays the external temperature when the
external temperature sensor is connected. If the temperature probe is faulty
the wording "
You can adjust the display contrast on the back panel. By rotating the variator
located on the vertical wall of the cover using a small screwdriver.
This symbol appears when
This symbol appears when the vehicle engine is running and the parallel
batteries is active or in the presence of the 230V mains when the two
batteries are in parallel verifing before the battery service voltage.
This symbol indicates that the alarm clock is enabled with related time. The alarm clock rings at the pre-set time
for 1 minute every 10 minutes; press any button to stop it ringing.
Pressing one of these buttons to view the TEST page, from which to check the voltage for the service B2 and
vehicle batteries B1, the level percentage %
percentage %
(0,100)
A bell is shown next to each indication
flashes.
If the tank is wrongly connected will show "
The screen remains active for approx. 30 seconds.
This written appears when there is an error communicating with NE185/NE196 shunt.
PROGRAMMING /
ALLARM:
Press this button from the first screen to enter the programming page.
With the arrow keys
the value to be changed. Now using the arrow keys change the selected value. While the exit key
function by saving the values
The pages available are:
- Date and time regulation
- Alarm clock time enabling and regulating
-
Alarm enabling:Tank S1 empty or Recovery tanks R1,R2 full.
When the alarm occurs in the panel buzzes (if enabled) intermittently for 5 sec. and at the same time shows the
TEST screen with the corresponding bell flashing.
-
Alarm enabling: Car battery (B1) less than 11,8V or Service battery (B2) less than 10V.
When the alarm occurs in the panel buzzes (if enabled) intermittently for 5 sec. and at the same time shows the
TEST screen with the corresponding bell flashing.
- Enabling the confirmation beep button pressed, and alarm buzzers
- Page info: displays the version of the panel and the shunt.
CONSUMPTION:
To turn on the control panel you must touch for 1 sec. the right or left side panel where there are the keys.
The panel after 30 sec. switches to standby mode by turning off all symbols except the keys
for 1sec. the right or left side panel.
On stand by (no active controls and no back lighting) the control panel with shunt NE185/NE196 consumes a total of approx
43mA. When the key
If the service battery voltage drops below 10V, after 1 minute the control panel turns itself off, together with all live parts.
CONNECTIONS:
The back of the panel has a connector for serial connection (CON3), a connector for the optional external temperature probe
(
TEMP OUT
) and a connector for the optional remote internal temperature probe (
If connecting the remote internal temperature probe must be cut and remove the temperature sensor of the pc-board
positioned between the support and the frame.
MEMORY BATTERY:
A buffer battery (LITHIUM 3V CR2032) is located on the back of the panel (removing the cover) to maintain the time in the
event of a power breakdown.
" will appear
in the position of the temperature value.
the 230V mains is connected
in the recovery tanks R1, R2
(
) (
)
change function, Press the enter key
is pressed the control panel turns itself off and total consumption is reduced to just 4mA.
Push button for turning
PUMP on or off
Push button for turning
AUX on or off
service battery voltage,
(0, 25, 50, 75, 100)
in the drinking water tank S1 and the level
if the relevant alarm is enabled. When the alarm is present the bell
" in the position of the value
(
3
and
)
repeatedly to enter the page and select
(
. Keys light up when you touch
TEMP IN
).
GB
)
exits the
