Uline H-161 Guia De Inicio Rapido
Uline H-161 Guia De Inicio Rapido

Uline H-161 Guia De Inicio Rapido

Termoselladoras de impulso
Ocultar thumbs Ver también para H-161:
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

H-161, H-163, H-190
H-293, H-306, H-458
H-963, H-1029, H-1252
Impulse sealers
• This machine does not have a power switch. Plug the
power cord into the outlet and set the timer knob
to the thickness of the materials to be sealed. (See
Part Identification to the right and Recommended
Settings Table on page 2.) The higher the number on
the dial, the longer the heat sealing time.
• Put one plastic bag on the sealing platform and
then push down the sealing arm. The sealer will
automatically control the seal time. Power is off
when the light turns off.
• After 1-2 seconds, slide the cutter (only on H-161 and
H-293) to trim the bag, then release the sealing arm.
(See Part Identification)
• If the bag seal is damaged or broken, it is because
the heating time is too long. Reset the timer knob to
a lower number.
• If the plastic bag sticks to the sealing arm, it was
because there was not enough cooling time. Keep
the arm down for a longer period of time after the
light turns off.
• It is okay to leave the unit plugged in. The unit is off
unless the sealing arm is down.
PAGE 1 OF 8
OperatIOn
PART IdEnTIFIcATIOn
Sealing Arm
Hinge Pin
Hinge
Bracket
Teflon Cover
Front Metal Plate
Power Cord
For Spanish, see pages 5-8.
Para Español, vea páginas 5-8.
BOTTOM VIEW
Pressure Plate
SEALING ARM
Assembly
(H-161, H-293, H-963
and H-1252 only)
Cutting Blade
Cutting Blade
Bracket Assembly
(H-161, H-293, H-963
and H-1252 only)
Rubber Pressure Pad
Heating Element
Sealer Body
Lower Teflon Tape
Pressure
Plate
Spring
Handle Knob
Rear Metal
Plate
Heating
Element
Cover
Timer Assembly
0513 IH-161
Tabla de contenido
loading

Resumen de contenidos para Uline H-161

  • Página 1 Bracket Assembly Sealing Arm (H-161, H-293, H-963 • After 1-2 seconds, slide the cutter (only on H-161 and and H-1252 only) Hinge Pin H-293) to trim the bag, then release the sealing arm. Handle Knob...
  • Página 2: Recommended Settings

    H-190 teflon tape for wear and damage. H-293 • Only use ULInE replacement parts. h-306 • A worn rubber pressure pad (under the handle) will H-458 influence the quality of the seats. The rubber pad should be periodically checked for uneven wear.
  • Página 3: Connection Diagram

    Heating Element Transformer Relay DC24V Sealing Light Source Timer Microswitch Connector Control P.C.B REPLAcEmEnT PARTS mOdel repair kit mOdel repair kit mOdel repair kit H-161 h-495 H-293 H-294 H-963 H-964 H-163 H-164 H-306 H-307 H-1029 H-1042 H-190 H-191 H-458 H-471...
  • Página 4 3. After removal of metal cover plates, teflon tapes and element, clean sealing surface (E) with cleaner, adhesive remover is recommended, until free of glue and debris. (See Figure 2) Figure 1 TOP VIEW Figure 2 π CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA 1-800-295-5510 uline.com PAGE 4 OF 8 0513 IH-161...
  • Página 5: Funcionamiento

    Bisagra Perilla de la Asa • después de 1-2 segundos, deslize la cortadora (solo Soporte en la H-161 y H-293) para cortar la bolsa, luego de Bisagra suelte el brazo. (Vea Identificación de Partes) Almohadilla de • Si el sello de la bolsa esta dañado o roto, es porque Goma de Presión...
  • Página 6: Configuraciones Recomendadas

    H-190 inferior de teflón para ver si está desgastada o H-293 dañada. h-306 • Solamente utilize partes de repuesto ULInE. H-458 • Si la almohadilla de goma de presión (abajo de la perilla) está desgastada esta afectará la calidad H-963 del sellado.
  • Página 7: Diagrama De Conexión

    Luz de Sellado Fuente Temporizador Microinterruptor Control P.C.B. Conector PARTES dE REPUESTO mOdelO KIT dE mOdelO KIT dE mOdelO KIT dE REPARAcIÓn REPARAcIÓn REPARAcIÓn H-161 h-495 H-293 H-294 H-963 H-964 H-163 H-164 H-306 H-307 H-1029 H-1042 H-190 H-191 H-458 H-471...
  • Página 8: Instrucciones Para Reemplazo De Cinta Y Resistencia

    (E), se recomienda usar removedor de adhesivo hasta que quede libre de todo el pegamento y residuos. (Vea diagrama 2) diagrama 1 VISTA SUPERIOR diagrama 2 π CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA 01-800-295-5510 uline.mx PAGE 8 OF 8 0513 IH-161...

Este manual también es adecuado para:

H-163H-190H-293H-306H-458H-963 ... Mostrar todo

Tabla de contenido