HIKOKI WH 14DSAL Instrucciones De Manejo página 9

CHARGING
Before using the power tool, charge the battery as follows.
<UC18YRSL / UC18YFSL>
1. Connect the charger's power cord to a receptacle.
When the power cord is connected, the charger's
pilot lamp will blink in red. (At 1-second intervals)
2. Insert the battery into the charger.
Firmly insert the battery into the charger, as shown
in Figs. 3, 4.
Before
charging
While
charging
Charging
complete
The pilot
lamp
lights or
Charging
blinks.
impossible
Overheat
standby
(2) Regarding the temperatures of the rechargeable battery
The temperatures for rechargeable batteries are as
shown in Table 2, and batteries that have become hot
should be cooled for a while before being recharged.
Table 2 Recharging ranges of batteries
Rechargeable batteries
BSL1430, BSL1440, BSL1415X,
BSL1830, BSL1840, BSL1850, BSL1815X
(3) Regarding recharging time
Depending on the combination of the charger and
batteries, the charging time will become as shown in
Table 3.
Table 3 Charging time (At 20°C)
Charger
Battery
BSL1415X, BSL1815X Approx. 20 min. Approx. 40 min.
BSL1430, BSL1830
BSL1440, BSL1840
BSL1850
NOTE:
The charging time may vary according to temperature
and power source voltage.
Indications of the pilot lamp
Lights for 0.5 seconds. Does not light for 0.5
Blinks
seconds. (off for 0.5 seconds)
(red)
Lights continuously
Lights
(red)
Lights for 0.5 seconds. Does not light for 0.5
Blinks
seconds. (off for 0.5 seconds)
(red)
Lights for 0.1 seconds. Does not light for 0.1
Flickers
seconds. (off for 0.1 seconds)
(red)
Lights
Lights continuously
(green)
〈UC18YRSL〉
Blinks
Lights for 1 seconds. Does not light for 0.5
(red)
seconds. (off for 0.5 seconds)
〈UC18YFSL〉
Temperatures at
which the battery
can be recharged
0°C – 50°C
UC18YRSL
UC18YGSL
UC18YFSL
Approx. 45 min. Approx. 90 min.
Approx. 60 min. Approx. 120 min.
Approx. 75 min. Approx. 150 min.
3. Charging
When inserting a battery in the charger, charging will
commence and the pilot lamp will light continuously
in red.
When the battery becomes fully recharged, the pilot
lamp will blink in red. (At 1-second intervals) (See
Table 1)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 1, according to the condition of the charger or
the rechargeable battery.
Table 1
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger firmly and pull out the battery.
NOTE
After operation, pull out batteries from the charger
first, and then keep the batteries properly.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries
and batteries that have not been used for an extended
period is not activated, the electric discharge might
be low when using them the first and second time.
This is a temporary phenomenon, and normal time
required for recharging will be restored by recharging
the batteries 2-3 times.
How to make the batteries perform longer
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery.
If you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the battery
and recharge it after it has cooled for a while.
English
Malfunction in the
battery or the charger
Battery overheated.
Unable to charge.
(Charging will commence
when battery cools)
8