Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Plug-in/Linking Directions
1
Fig. 1
2
the fixture. The linking cord is fitted with a distinct plugs at each end of the cord. Similarly,
the linking cord only plugs in with the correct plug/receptacle combination. Trace the line
cord over to the nearest outlet, and plug in. Your fluorescent light is ready to use.
If you are installing a second, or third fixture, and simply need to connect it to a previously
3
installed fixture, follow the instructions outlined in Steps 1 and 2. Make sure that the
distance between fixtures does not exceed the connector cord length.
4
Bulb Replacement Instructions
Replace only with a linear fluorescent bulb: G9712L-T5-WHESI (12.375 in.) Bulb #F8T5;
G9724L-T5-WHESI (22.625 in.) Bulb #F14T5. Do not replace with any other wattage of linear
fluorescent bulb. These bulbs are readily available at your local home center and most larger
hardware store.
1
Fig. 1
Fig. 1
2
Fig. 2
Fig. 2
3
Install the replacement bulb into the sockets by aligning the pins of the bulb with the slot in
the sockets. Using your thumbs and forefinger, press the metal ends of the bulb socket and
roll the bulb forward until it rotates 90 degrees inside the socket, making contact between
the bulb pins and the socket contacts. Place the diffuser in the top lip. Push the grooved
edge of the diffuser down into the bottom edge until it locks in. Restore power to your
fixture.
4
Dispose of the old lamp(s) in accordance to local, state, and/or federal laws, or go to
www.lamprecycle.org for more information.
Troubleshooting Guide
Minor problems often can be fixed without the help of an electrician. Before doing any work on the
fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.
Problem
Fixture doesn't light
Fuse blows or circuit breaker
trips when light is turned on
In the unlikely event that your fixture's ballast, or lamp socket(s) fail, they can be replaced by a
qualified electrician. For further information regarding these replaceable parts, please have your
electrician contact our technical support number at 1-800-291-8838.
Cleaning Instructions
Your fixture is made from quality materials that will last for many, many years with
minimum care. You may want to periodically clean the fixture using a mild, non-abrasive
glass cleaner and soft cloth. Do NOT use solvents or cleaners containing abrasive
agents. When cleaning the fixture, make sure you have the power turned off and do not
spray liquid cleaner directly onto the bulb, socket, ballast, or wiring.
Replacement Parts List
Keep this guide handy for
ordering replacement parts.
Using a screwdriver, or other similar tool, pry off the plastic
receptacle cap that covers the input receptacle in order to
insert the power cord (Fig. 1).
Attach the power cord to the "Power-In" receptacle on one end
Fig. 2
of the fixture (Fig. 2). The 2 receptacles are designed to only
accept a specific plug (see illustrations on page 1). NOTE: The
Power Cord will only plug into one end correctly, do not try to
force it into the wrong receptacle, this could cause damage to
Once the second fixture is installed, plug the connector cord
into the receptacle on the end of the fixture, and plug the other
end of the connector cord into the receptacle of the previously
installed fixture (Fig. 3). Your fluorescent light bar has a two
position rocker switch on the face of the unit. Each bar is
individually operated and dimmed. Therefore, you don't need
Fig. 3
to have the entire chain lit if you only need light in a specific
area. Simply turn on the lights that you need.
Remove the diffuser by pulling back and up on the top edge of
the diffuser using your fingertips (Fig. 1).
Remove the bulb from the fixture by placing your thumbs on
Fig. 3
the socket and set aside during mounting.
Cause
Bulb is defective
Power is off
Bad plug connection
Bad switch
Crossed wires or power wire
is grounded out
the metal ends of the bulb (Fig. 2). While
applying slight pressure on the bulb, roll the
bulb toward you until the contact pins on the
ends of the bulb disengage from the
socket (Fig. 3). Pull the bulb straight out from
Hardware Kit
HDW9712L
HDW9724L
- 4 -
Solution
Replace bulb
Check if power supply is on
Check wiring
Test or replace switch
Check wiring connections
Tabla de contenido
