Idiomas disponibles
Idiomas disponibles
LIGHT LEVEL
REGULATOR
LIGHT LEVEL
SENSOR
The ECOMAT MINI movement detector is capable of detecting the slightest
movement because of its high-frequency technology. Its detection precision does
not depend on the ambient temperature. It immediately detects any movement,
even those of inert elements, such as doors or chairs.
The ECOMAT MINI can detect within a five-metre radius of action, with 360º
coverage.
INSTALLATION
The assembly and installation of electric apparatus must be carried out by
authorised personnel.
The unit is internally protected against interference by a security circuit. However,
certain especially strong magnetic fields can alter its operation.
WARNING: Disconnect the power supply prior to installing the unit.
Installation suggestions
The equipment can penetrate non-metal materials, such as wood, brick and
plaster.
It should not be installed in locations with vibrations.
Switch the power off before changing lamps.
The unit must be installed at more than 6 cm from the ballast.
It must be installed in a dry location and well away from any possible splashing.
It must not be installed in front of metal objects because this could negatively
affect detection distances. The equipment microwaves cannot penetrate metal
objects.
The ECOMAT MINI detects the reflections of the emitted microwaves so that
detection is enhanced in closed volumes, such as corridors, doorways,
bathrooms and offices, but will be reduced in large or open spaces, such as
garages and porches etc.
MOUNTING
Example of an installation on a false ceiling (non-metallic):
CEILING
The sensor must be facing to the zone where we want to detect.
ENG
ECOMAT MINI
MOVEMENT DETECTOR
SENSOR
FALSE CEILING
(NON METALLIC)
CONNECTION
Connect according to the following drawing:
L
N
A wrong connection can damage the equipment.
PUTTING INTO SERVICE
There are three potentiometers behind the front cover:
TIME: Allows timing adjustment from five seconds to thirty minutes. Timing
commences after detecting the last movement.
METER: The detecting range is adjustable between 2 and 10 metres
LUX: Adjustable between 5 Lux (night) and 2,000 Lux (day).
Thirty seconds after being switched on, the sensor enters normal operation. Set
the TIME potentiometer to TEST mode.
FUNCION TEST
This function is used to verify the required detection zone.
The METER adjustment sets the equipment range from a two to ten-metre
diameter.
When movement detection occurs, the equipment red LED and the associated
lighting comes on for two seconds, independently of the LUX setting.
After verifying the detection mode, the TIME potentiometer should be set to the
desired lighting switch-on time after detection, which is between 5 seconds and 30
minutes. The LUX potentiometer is then set to the lighting level above which the
equipment must not switch on the lighting.
In order for the equipment adjustment potentiometers to be taken into effect,
it is necessary to abandon the detection zone and wait for the installation to
switch off.
PERMANENT MODE (ON 4 hours)
In order to switch the equipment permanently on for four hours, independently of
the regulated lighting level, the power supply must be switched Off – On – Off – On
in less than two seconds. Flashing will occur to indicate that the equipment is in
Permanent mode. The LED will flash one second on and five seconds off
throughout this four-hour period.
This mode is abandoned by switching the power supply off for more than two
seconds.
TECHNICAL SPECIFICATIONS
Power supply
Sensor
Breaking power
Maximum recommended loads:
Incandescent lamps
Fluorescents
Low voltage halogens
Halogens (230 V ~)
Low consumption lamps
Downlights
Led
Own consumption
Capture angle
Detection range
Detection field (Meter)
Brightness range (Lux)
Timing range (Time)
Operation temperature
Degree of protection
Hereby,
ORBIS TECNOLOGÍA ELÉCTRICA S.A.
type
is in compliance with Directive 2014/53/EU. The full text of the
ECOMAT MINI
EU declaration of conformity is available at the following internet address:
http://www.orbis.es/downloads/declarations-of-conformity
DIMENSIONS
31.5
ORBIS TECNOLOGÍA ELÉCTRICA, S.A.
Lérida, 61
Teléfono:+ 34 91 5672277;
230 V~ 50-60 Hz
5,8 GHz
μ 6 A 230 V~ cos φ = 1
1000 W
160 VA/ 20µF
200 VA
500 W
150 VA
150 VA
200 VA
10 VA (1 W)
360º
Up to 10 m in diameter at 2.5 m high
From 2 m to 10 m in diameter
From 5 to 2000 Lux
From 5 seconds. to 30 minutes
From -20 ºC to +50 ºC
IP 20 in accordance with EN60529
declares that the radio equipment
90
E–28020 MADRID
Fax:+34 91 5714006
E-mail: [email protected]
http://www.orbis.es
