Echo MS-300 Manual Del Propietário

IF YOU HAVE ANY QUESTIONS OR CONCERNS, OR ARE MISSING PARTS DO NOT RETURN SPRAYER TO IF YOU HAVE ANY QUESTIONS OR CONCERNS, OR ARE MISSING PARTS DO NOT RETURN SPRAYER TO
THE STORE! PLEASE CALL OUR HOT LINE AT 1-800-253-4642 THE STORE! PLEASE CALL OUR HOT LINE AT 1-800-253-4642
Year Round: Mon. – Fri., 8:00 a.m. to 7:00 p.m., ET March 1 – August 31: Sat. and Sun., 10:00 a.m. to 4:00 p.m., ET Year Round: Mon. – Fri., 8:00 a.m. to 7:00 p.m., ET March 1 – August 31: Sat. and Sun., 10:00 a.m. to 4:00 p.m., ET Year Round: Mon. – Fri., 8:00 a.m. to 7:00 p.m., ET March 1 – August 31: Sat. and Sun., 10:00 a.m. to 4:00 p.m., ET
For all other ECHO products, call Consumer Product Support at 1-800-432-3246 For all other ECHO products, call Consumer Product Support at 1-800-432-3246
WARNING!!! THIS PRODUCT IS DESIGNED TO SPRAY CHEMICALS THAT MAY BE HARMFUL AND COULD CAUSE
SERIOUS PERSONAL INJURY IF INHALED OR BROUGHT INTO CONTACT WITH THE USER. FAILURE TO READ AND
FOLLOW OWNERS' MANUAL INSTRUCTIONS BEFORE USE AND/OR MISUSE OF THIS PRODUCT COULD RESULT IN
EXPLOSIVE FAILURE WITH MAJOR INJURIES.
• ALWAYS water test sprayer before each use.
• ALWAYS wear long sleeve shirts, long pants, goggles, gloves and durable shoes.
• ALWAYS READ AND FOLLOW label instructions for the chemicals to be applied.
• AFTER USE release pressure and clean the sprayer.
ALWAYS RELEASE pressure in sprayer before servicing.
•
DO NOT alter the sprayer or any components.
•
DO NOT spray flammable, caustic (i.e. acids, chlorines and bleach), corrosive, heated or self-heating solutions with
•
this sprayer.
• DO NOT store liquids in the sprayer.
• NEVER fill tank above the "3G" line on the tank.
Attaching Wand to Flow Control
1. Ensure that the gasket is in the open end of the flow control.
2. Insert the non-threaded end of the wand into the open end of
the flow control.
3. Tighten the screw cap.
Attaching Hose to Flow Control
1. With petroleum jelly, lubricate the o-ring on the large hose insert.
2. Push the large hose insert into the handle end of the flow control until fully seated.
3. Slide the hose spring nut onto the flow control and screw on; hand tighten only.
Attaching Hose to Tank
1. Insert open end of black supply tube into the small black hose insert until snug.
2. With petroleum jelly, lubricate the hose insert o-ring.
3. Fully insert hose insert/supply tube assembly into threaded tank nipple, slide spring nut to the tank nipple and screw
on. Hand tighten only.
Changing the Nozzle from Adjustable Cone to other patterns
1. Unscrew #1 adjustable poly cone nozzle cap
2. Unscrew #8 retaining nut
3. Push #6 nozzle body with o-ring out of #8 retaining nut
You are now ready to change to a different spray pattern.
Follow the "Spayer Tip Assemblies" diagram for your desired
spray pattern.
Sprayer Tip Assemblies:
1. Poly Adjustable Cone
3. Jet Cap
5. Elbow
7. Flat Fan Tip
Operation
1. Turn pump handle counterclockwise to remove pump.
2. Fill tank with desired chemical solution, careful to follow chemical manufacturers' guidelines.
3. Tighten pump assembly for a good seal.
4. To pressurize the tank, pump the pump handle; to spray, squeeze flow control lever.
5. Prior to every removal of the pump release pressure by turning pressure relief valve once to the right until it snaps.
.
Before repressurizing, turn it one more time to the right until it snaps.
Servicing the Pump
1. Remove pump from tank.
2. Unscrew cap at top of the pump cylinder in counter-clockwise motion.
3. Remove plunger assembly from cylinder.
4. When reassembling, be sure square tabs on lock plate are fitted into cylinder notches, then screw cap on.
1. Remove pump assembly from the tank.
2. Unlock the pump handle and pull it out as far as it will go.
3. Place a flat blade screwdriver in the slot below  PRY  . Move the screwdriver
handle down towards the bottom of the pump, prying the cap out and around the
tab. Put a wedge in opening. Repeat this procedure on the other side of the
pump cap.
4. To reassemble, insert the plunger assembly into the cylinder and snap the cap
back into place.
Operators Manual
2. Gasket
4. Swirl Plate
6. Nozzle Body w/o-ring
8. Retaining Nut
Model MS-300
8
8
3
7
4
2
5
Flat
Fan
8
8
1
3
2
2
2
5 5
Hollow Poly Jet
Cone Adjustable Stream
5
971-297
11/13