Nice ETPB Instrucciones Y Advertencias De Instalación Y Uso página 11

the reader. The reader emits an acoustic signal and immediately enables the ma-
noeuvre. At the same time LED "L1" (fig. 7) flashes, then pauses to signal the
type of manoeuvre in progress.
02. Choose the new required manoeuvre from Table 4 and make a note of the "L1"
LED flash signals associated with the manoeuvre.
03. Press the "T" key (once or twice) to display the list of available commands, until
you have set the manoeuvre command chosen in point 02 (every time the key is
pressed, LED "L1" flashes once more than for the previous time).
04. Pass the card used in point 01 in front of the reader: the reader emits an acoustic
signal and immediately enables the new manoeuvre; at the same time, LED "L1"
flashes then pauses to signal that the new manoeuvre has been set.
8.3.2 - Procedure to change manoeuvre command no. 1, with a
card programmed to enable BOTH COMMANDS
01. Hold the card whose manoeuvre command you wish to change in front of
the reader. The reader emits an acoustic signal and, after 1 second, emits another
enabling the manoeuvre. At the same time LED "L1" (fig. 7) flashes, then pauses
to signal the type of manoeuvre in progress.
02. Choose the new required manoeuvre from Table 4 and make a note of the "L1"
LED flash signals associated with the manoeuvre.
03. Press the "T" key (once or twice) to display the list of available commands, until
you have set the manoeuvre command chosen in point 02 (every time the key is
pressed, LED "L1" flashes once more than for the previous time).
04. Hold the card used in point 01 in front of the reader. The reader emits an acoustic
signal and after 1 second, emits another, immediately enabling the new manoeu-
vre. LED "L1" flashes, then pauses to signal that the new manoeuvre has been set.
8.3.3 - Procedure to change manoeuvre command no. 2, with a
card programmed to enable BOTH COMMANDS
01. a) - Pass the card in front of the reader (the card whose manoeuvre command
is to be changed): when you hear an acoustic signal, remove the card immedi-
ately from the reader; then...
b) - (within 2 seconds) re-pass the card in front of the reader. The reader emits
an acoustic signal and immediately enables the manoeuvre. At the same time
LED "L1" (fig. 7) flashes, then pauses to signal the type of manoeuvre executed.
02. Choose the new required manoeuvre from Table 4 and make a note of the "L1"
LED flash signals associated with the manoeuvre.
03. Press the "T" key (once or twice) to display the list of available commands, until
you have set the manoeuvre command chosen in point 02 (every time the key is
pressed, LED "L1" flashes once more than for the previous time).
04. a) - Pass the card used in point 01 in front of the reader: when you hear an acous-
tic signal, remove the card immediately from the reader; then...
b) - (within 2 seconds) re-pass the card in front of the reader. The reader emits an
acoustic signal and immediately enables the manoeuvre. At the same time LED
"L1" (fig. 7) flashes, then pauses to signal the type of manoeuvre set.
TABLE 4 - Manoeuvre command associated with command no. 1 or
command no. 2 of a card
Led "L1" signal Manoeuvre command
STEP-BY-STEP (associated with command no. 1) by
1 flash + pause
factory
2 flashes + pause OPEN
3 flashes + pause CLOSE
PARTIAL OPEN (associated with command no. 2) by
4 flashes + pause
factory
5 flashes + pause STOP
6 flashes + pause COURTESY LIGHT
English – 9