Ocultar thumbs Ver también para PRO Serie:
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

ASSEMBLY INSTRUCTIONS
1.
Pull bail pin from Mounting Bracket and Arm Assembly.
2.
Attach Main Support tube to Mounting Bracket in orientation shown (see Diagram 1). Line up the hole near end of
main support tube with the hole in Mounting Bracket and install one (1) ½" x 3-1/4" lg. hex bolt, two (2) nylon flat
washers, and locknut as shown. Tighten locknut until it is snug. Main Support tube still must rotate following
tightening.
3.
Re-install bail pin thru Mounting Bracket and Main Support tube so bike carrier is in the upright position.
4.
Attach Arm Assembly to Main Support tube as shown. Line up the hole in end of support tube with hole in Arm
Assembly. Re-install bail pin thru Arm Assembly and Main Support tube.
Diagram 1
Lock Nut
Nylon
Washers
Vehicle Mounting:
1.
1-1/4" Receiver hitch use anti-rattle pin and clip as shown. Tighten with ¾"
wrench (not provided). Insert pin from drivers side only.
2.
2" Receiver hitch use 2" Adapter, anti-rattle pin and clip as shown. Tighten
with ¾" wrench or socket (not provided). Insert pin from drivers side only.
Cequent Performance Products
Plymouth, MI 48170
ITEM
DESCRIPTION
Arm Assembly
Main Support Tube
Bail Pin
Page 1 of 9
63144
:
:
4 Bike Carrier
Mounting Bracket
Bail Pin
Hex Bolt
2"
Adapter
Anti-
Rattle Pin
Washer
Clip
Diagram 2
63144N
Rev A 08-11
Printed in XXXXXX
loading

Resumen de contenidos para Cequent Performance Products PRO Serie

  • Página 1 (not provided). Insert pin from drivers side only. 2” Receiver hitch use 2” Adapter, anti-rattle pin and clip as shown. Tighten with ¾” wrench or socket (not provided). Insert pin from drivers side only. Diagram 2 Cequent Performance Products Plymouth, MI 48170 63144N Rev A 08-11...
  • Página 2 To restore the rack to the upright position, do reverse procedure. Check periodically to insure you have a solid fit between the rack and the mounting location. Cequent Performance Products Plymouth, MI 48170 63144N Rev A 08-11...
  • Página 3 • Improper mounting will void the rack warranty. • Damage to bicycles or rack due to ground clearance problems are not covered by warranty. • Not for off road use. Cequent Performance Products Plymouth, MI 48170 63144N Rev A 08-11...
  • Página 4: Descripción

    2 "enganche utilizar 2" adaptador, anti-sonajero pin y el clip como se Diagramme 2 muestra. Apriete con ¾ "llave o (no incluido). Inserte el pasador del lado del conductor solamente. Cequent Performance Products Plymouth, MI 48170 63144N Rev A 08-11...
  • Página 5 Para restaurar el portabicicletas a la posición vertical, realice el procedimiento inverso. Revise periódicamente para asegurar que hay un ajuste firme entre el portabicicletas y la ubicación de montaje. Cequent Performance Products Plymouth, MI 48170 63144N Rev A 08-11 Printed in XXXXXX...
  • Página 6 • El montaje incorrecto invalidará la garantía de la parilla. • El daño a las bicicletas o parilla debido a problemas de despeje del piso no está cubierto por la garantía. • No use fuera de la carretera. Cequent Performance Products Plymouth, MI 48170 63144N...
  • Página 7 2 "accroc utilisation du récepteur 2" Adapter, anti-cliquetis des broches et Diagrama 2 clip comme montré. Serrez avec ¾ "clé ou douille (non fourni). Insérez épingle du côté conducteur seulement. Cequent Performance Products Plymouth, MI 48170 63144N Rev A 08-11...
  • Página 8 à l’écart de la charnière durant cette manoeuvre. Inverser la procédure pour remettre le support à vélos à l’endroit. Vérifier périodiquement que le support est fixé solidement sur les points de montage. Cequent Performance Products Plymouth, MI 48170 63144N Rev A 08-11...
  • Página 9 • Les dommages au vélo ou au porte-vélos causés par un problème lié à la garde au sol ne sont pas couverts par la garantie. • Ce porte-vélos ne convient pas à utilisation hors route. Cequent Performance Products Plymouth, MI 48170 63144N...

Este manual también es adecuado para:

Pro 63144