Tabla de contenido
Idiomas disponibles
Idiomas disponibles
ENGLISH
Replacement parts
Warning!To reduce the risk of personal injury, disconnect
battery pack from tool and engage trigger lock-off before
performing maintenance, or clearing a jammed nail.
The tool comes equipped with a spare no mar tip located on
the side of the nail magazine.
Use only identical replacement parts. For a parts list or to
order parts, visit our service website at www.stanley.eu/3co.
uk. You can also order parts from your nearest
BLACK+DECKER Factory Service Center or
BLACK+DECKER Authorized Warranty.
Accessories
Warning! Since accessories, other than those offered by
BLACK+DECKER, have not been tested with this product,
use of such accessories with this tool could be hazardous. To
reduce the risk of injury, only BLACK+DECKER recommended
accessories should be used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
Troubleshooting
If your appliance seems not to operate properly, follow the
following instructions.
If this does not solve the problem, please contact your local
BLACK+DECKER repair agent.
Warning! Before proceeding, unplug the appliance.
Problem
Possible Cause
Unit will not start.
Battery pack not
installed properly.
Battery pack not
charged.
Trigger lock-off is
engaged.
Tool doesn't
Motor stops running
actuate.
after 2 seconds.
(Headlights on,
motor does not
run)
Tool doesn't
Low battery charge or
actuate.
damaged battery.
(Headlights
flash)
Tool doesn't
Jammed fastener / tool
actuate.
stalled.
(Headlights flash
continuously)
Jammed mechanism
Tool doesn't
actuate.
((Headlights on,
motor runs,
driver blade
stuck down)
12
(Original instructions)
Possible Solution
Check battery pack
installation.
Check battery pack charging
requirements.
Disengage trigger lock-off.
Normal operation; release
trigger or contact trip and
re-depress.
Charge or replace battery.
Remove the battery, rotate the
stall release lever. Clear the
jammed fastener, and reinsert
battery pack.
See authorized service center.
See authorized service center.
Problem
Possible Cause
Tool operates,
Low battery charge or
but does
damaged battery.
not drive the
fastener fully.
Depth adjustment set
too shallow.
Tool not firmly applied
to workpiece.
Material and fastener
length too rigorous an
application.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory opera-
tion depends upon proper tool/appliance care and regular
cleaning.
Warning! Switch off and unplug the appliance before carrying
out any cleaning.
Dirt and grease may be removed from the exterior of the
u
appliance using a cloth.
Warning! NEVER use solvents or other harsh chemicals
for cleaning the non-metallic parts of the appliance. These
chemicals may weaken the materials used in these parts. Use
a cloth dampened only with water and mild soap. Never let
any liquid get inside the unit; never immerse any part of the
unit into a liquid.
Warning! NEVER spray or in any other way apply lubricants
or cleaning solvents inside the tool. This can seriously affect
the life and performance of the tool.
Service Notes
This product is not user serviceable. There are no user
serviceable parts inside the nailer. Servicing at an authorized
service center is required to avoid damage to static sensitive
internal components.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Possible Solution
Charge or replace battery.
Rotate depth adjustment
wheel to
a deeper setting.
Read instruction manual.
Choose appropriate material
or fastener length.
Tabla de contenido
