Commissioning/Decommissioning; Installation; Installing The Cutting Blade (03); Renewing The Cutting Blade (04) - AL-KO GS 7,2 Li Instrucciones De Uso

Commissioning/Decommissioning

4 COMMISSIONING/
DECOMMISSIONING
CAUTION!
Risk of injury
Sharp-edged and moving appliance parts
can lead to injury.
■
Always wear protective gloves during

installation.

■
Before the installation steps, always
put the respective blade guard on the
cutting blade.
4.1 Installation
4.1.1

Installing the cutting blade (03)

1. First insert the cutting blade in the support
(03/2) as shown in the example of the grass
blade (03/1) (03/a).
2. Let the front part of the grass blade engage
in the appliance (03/b) with light pressure.
The engaging must be clearly audible.
3. Remove the blade guard (03/c).
4.1.2

Renewing the cutting blade (04)

WARNING!
Danger of lacerations
The cutting blades continue to run after
switching off the engine. Danger of lacer-
ations when reaching into sharp-edged
and moving appliance parts.
■
Never reach directly into moving ap-
pliance parts after switching off the
appliance.
■
Wait until the cutting blade come to a
standstill before changing it or clean-
ing the appliance of cuttings.
■
Wear protective gloves.
1. Put on the blade guard (04/2).
2. Firmly press both unlocking knobs (04/1) (04/
a), and take the cutting blade (04/2) out of
the appliance (04/b).
3. Insert the other cutting blade (04/3) into the
support (04/c).
4. Let the unlocking knobs (04/1) engage. The
engaging of the cutting blade must be clearly
audible.
441884_a
4.1.3

Attaching the grass collector (05)

For using the grass cutter on the edge of a
garden bed, the grass collector can be attached
to the grass blade. It straightens up the grass and
prevents the cut-off grass from falling into the
bed.
1. Put the grass collector (05/1) on the under-
side of the grass blade so that the two pins
(05/2) point towards the openings and the
screw lies in the slotted hole (05/3).
2. Push the grass collector (05/1) into the two
openings (05/a) with low pressure.
4.2

Charging the rechargeable battery (06)

The rechargeable battery is partially charged.
Fully charge the rechargeable battery before us-
ing it for the first time. The rechargeable battery
can be charged in any charge status. Interrupting
charging does not damage the rechargeable bat-
tery.
■
The handle of the appliance can become hot
during the charging process. This is normal.
■
Do not use the appliance during the charging
process.
■
The operating time of the rechargeable bat-
tery grass and shrub cutter depends on the
status of the rechargeable battery and the
properties of the cuttings (thickness, etc.).
Frequent switching on and off reduces the
operating time. For details, see "Technical
data".
1. Insert the mains plug (06/1) into the power
socket.
2. Insert the charge plug in the charging socket
of the rechargeable battery grass and shrub
cutter (06/3). The charging process begins
with the constant lighting of the green LED
display (06/2) on the mains plug. The LED in-
dicates that current is flowing. The charging
process is indicated by the LED on the appli-
ance (06/4): The rechargeable battery is fully
charged when the LED on the appliance
(06/4) lights constantly.
3. Unplug the mains plug (06/1) from the power
socket and from the charging socket (06/3).

5 OPERATION

5.1

Switching the appliance on/off (07)

Switching on the appliance
1. Push the unlocking knob (07/1) forwards (07/a).
19