Idiomas disponibles
Idiomas disponibles
STEP 2: Mounting the End Supports onto the roof
A.
The Pads all have a vehicle roof position identification initial on the top
inside surface of the pad. (FR, FL, RR, RL)
Ensure Mount Pads correspond with mount positions on the vehicle.
FR = Front Right; FL = Front Left
RR = Rear Right; RL = Rear Left.
B.
Place the pads as shown in Figs 4a & 4b.
C.
With one strap mated around the door return, flex out the second
strap out and around the other door-return ensuring the protective
rubber on the inside of the strap doesn't peel back.
D.
Using the security key supplied, tighten the bolt to pull the strap upwards
against the vehicle's door return.
Whilst tensioning the straps, alternating from left to right straps to ensure
an even tention on both sides (Fig 4c.) of the crossbar is attained.
Tighten the bolts to a firm hand tightness (approx 5 Nm).
STEP 3: Fitting End Support Covers to the End Supports
Ensure the Lock Barrels have been inserted into the End Support
Covers before assembly.
A.
Locate the ends of the hinge with the cover mount holes.
Flex the hinge ends together and line themup up with the cover
mount holes.
Push the ends through the holes until capped heads of the hinge
have entirely pushed through (Fig 5a).
Be very careful with flexing hinges so as not to break them
B.
Ensure hinge has been mounted correctly by pushing the ends of
the hinge through the holes in the end support cover until you hear
an audible "click" (Fig 5b).
Fully extend the End Support cover away from the End Support.
C.
Pivot the end support cover on the hinge whilst pushing the top of
the end support cover downwards until the end support cover is
held fixed in place (Fig 5c).
STEP 4: Closing the End Support Covers
A.
Using the Security Key, tighten the 50mm Bolts to approx. 7Nm of
torque or a firm hand-tightness.
B. Store security key in it's storage location in the End Support (Fig. 7b)
C.
Close the End Support Covers by flipping the cover down and
pushing hard up against the End Support (Fig 6a). You should hear
an audible "click" when the cover has engaged with the End Support.
D.
Lock the covers into place using the Key provided. Remove Keys
and store in a safe place.
STEP 5: Using the Roof Racks
A.
Refer to 'Care for your Racks' to maintain your Roof Racks.
B.
To load accessories into the Channel of the Cross Bars, unlock the
End Support Cover (Fig. 7a). Pull the Cover out and down to fully
access the Channel. Once accessories have been loaded, replace
the End Support Cover and lock.
Intermittently check that all Screws and Bolts are sufficiently tightened
whilst the Roof Racks are in use.
www.rolaproducts.com
Cequent Performance Products - Plymouth, MI
Technical Service: (888)521-0510
HYUNDAI ELANTRA TOURING
2009 - on
Fig 4a.
Front Right Pad Shown.
Fig 4b.
26 3/4"
690mm
Fig. 5a
End Support
Cover
End Support
Fig. 5b
Fig 6a.
Fig. 7a
Fig 4c.
Fig 4c.
Front of vehicle
7 1/2"
190mm
Front
Fig 3b.
Rear Right End Support Shown.
Cross Bar
Fig. 5c
CLICK
Fig 6b.
Key
Fig. 7b
Key Storage location
Note: You will have to remove or trim
the Buffer Strip to mount accessories
59800
Front of vehicle
Buffer Strip
CLICK
Access to
channel
Issue A
59800N
03/05/09
Sheet 1 of 2
PRINTED IN AUSTRALIA
Printed in XXXXX
