Troubleshooting Guide - NuTone LA-204WH Instrucciones De Instalación Y Funcionamiento

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

PREPARING THE RECEIVER
RECEIVER SECURITY CODING
Refer to Figure 5.
Changing the Security Code is not necessary unless you have
changed the security code in the Transmitter. Both the Transmitter
and Receiver codes must match.
1. Remove the screw from the code switch cover, then remove
cover.
2. Refer to Figure 6. Set the switch in the Receiver to match the
jumpers in the Transmitter. The jumpers that are installed in the
Transmitter must correspond to the switched set to the ON
position in the Receiver. For example, if jumper #1 is installed,
Switch #1 is in the ON position.
3. After setting the switches, reinstall the code switch cover with
screw.
MOUNTING THE RECEIVER
1. Plug the Receiver into any 120 volt wall outlet. Outlet must be
located within 100 feet of the Transmitter.
WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period
of one (1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
During this one year period, NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, FILTERS, DUCT, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES
FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident,
improper maintenance or repair (other than by NuTone), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty
lasts, so the above limitation may not apply to you.
NUTONE'S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE'S OPTION, SHALL BE THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY. NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH
PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.
WARRANTY SERVICE: To qualify for warranty service, you must (a) notify NuTone at the address stated below or telephone 1/800-543-8687, (b) give the model
number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present
evidence of the original purchase date.
Date of Installation
Model No. and Product Description
Residents of Alaska or Hawaii should write to: NuTone Inc. Attn: Department of National Field Service, 4820 Red Bank Road, Cincinnati Ohio 45227-1599.
Residents of Canada should write to: Broan-NuTone Canada, 1140 Tristar Drive, Mississauga, Ontario, Canada L5T 1H9.
Product specifications subject to change without notice.
REMOVE SCREW
AND COVER
FIGURE 5
One Year Limited Warranty
Builder or Installer
IF YOU NEED ASSISTANCE OR SERVICE:
For the location of your nearest NuTone Independent Authorized Service Center:
Residents of the contiguous United States Dial Free 1-800-543-8687
Please be prepared to provide:
Product model number • Date and Proof of purchase • The nature of the difficulty
TOP
P.C.
BOARD
BATTERY
LOCATION

TROUBLESHOOTING GUIDE

PROBLEM
1. Chime does not sound.
2. Chime is activated by another
wireless device.
3. When transmitter button is pressed,
the incorrect chime sound is heard.
SECURITY
CODE
SETTING
JUMPERS
INSTALLED
ON 1, 3 & 6
SOLUTION
Check batteries and polarity in
transmitter.
Make sure transmitter is not located on
metal surface.
Check that outlet on receiver has power.
Check receiver and transmitter security
code. These codes must match.
Change the security code in the
transmitter and receiver.
These codes must match.
Check the sound code jumpers in the
transmitter.
Rev. 01/2005
4820 Red Bank Road, Cincinnati, Ohio 45227
Printed in China, Part No. 88328, 04/07
FIGURE 6
Tabla de contenido
loading

Este manual también es adecuado para:

La-207twh

Tabla de contenido