Idiomas disponibles
Idiomas disponibles
Application
In order to ensure correct operation, a pressure of at least 14 psi is
necessary at the shower system.
Caution:
With sufficient power electric or gas instantaneous heaters are also
suitable.
All thermostats are adjusted in the factory at a flow pressure on both sides
of 45 psi.
Should temperature deviations exist due to special installation conditions,
the thermostat must be adjusted to the local conditions (see Adjustment).
Specifications
Minimum flow pressure
Max. working pressure
Recommended flow pressure
Test pressure
Flow rate at 3 bar flow pressure
Hand spray
max. flow 9,5 L/min or 2,5 gpm/ 80 psi
Side showers
max. flow 9,5 L/min or 2,5 gpm/ 80 psi
Handspray and side sprays
max. flow 9,5 L/min or 2,5 gpm/ 80 psi
Max. water temperature at hot water inlet
Recommended max. flow temperature
(energy saving)
Safety check
Hot water temperature at supply connection min. 4 °F higher than mixed
water temperature
Cold water connection
Hot water connection
If static pressure is greater than 72.5 psi, fit pressure reducer.
Tools required, see fold-out page I.
Delivery specification, see fold-out page II.
Installation
New installation:
Make up unions.
For union dimensions for cold and hot water connection, see fold-out
page III Fig. [1].
The cold water supply must be connected on the right and the hot water
supply on the left.
The installation dimensions of the fitting relate to the standing level of the
shower stand, see Fig. [2].
The installation height of the showers from the standing level must be
observed in order to comfortably operate the fitting.
Retrofitting:
Union dimensions must correspond to Fig. [3].
The cold water supply must be connected on the right and the hot water
supply on the left.
The installation dimensions of the fitting relate to the standing level of the
shower stand, see Fig. [4].
The installation height of the showers from the standing level must be
observed in order to comfortably operate the fitting.
Connections and fastenings, see fold-out page III and IV, Figs. [1]
to [10].
For individual components, see delivery specification, Figs. [I] to [IV].
1.Drill fixing holes for ø 8mm mounting plugs, see Fig. [1] and [3].
2.Install accompanying elbow unions (A). If S-unions are present, remove
and replace with elbow unions (A), see Fig. [5].
3.Screw in threaded studs (A1) into the elbow unions (A) using roughly
one turn.
Seal the elbow unions (A) at the tiled wall with sealing compound.
Flush pipes thoroughly
Please pass these instructions on to the user of the fitting.
1
The right to make technical modifications is reserved.
English
4.
Remove retaining rings (B) with installation tool (B1),
see Fig. [6].
5.
Detach wall plate (B2).
6.
Insert mounting plug (C1), see Fig. [7].
7.
Guide elbow unions (A) through the area provided in the fitting
assembly (C) and slide rib (A2) from below behind the lug (A3) of the
elbow union, see Fig. [8].
8.
Preassemble the fitting assembly (C) with the threaded studs (A1).
9.
Secure fitting assembly (C) using fixings (C2) supplied, see Fig. [7].
10. Connect hoses (D) with accompanying seals (D1) and elbow
unions (A), see Fig. [9].
21.75 psi
Spray hose, shower rail slider, shower rail and hand spray, see fold-
145 psi
out page IV and V, Fig. [9], [10] and [11].
14 - 72.5 psi
For individual components, see delivery specification, Figs. [IV], [V], [VI]
232 psi
and [VII].
1.Attach spray hose (E) with seal (E1) to elbow unions (E2), see Fig. [9].
2.Slide shower rail slider (F) onto shower rail (F1), see Fig. [10].
3.Insert shower rail (F1) into the fitting assembly (C) and secure using
176 °F
screw (F2).
4.Insert bracket (F3) onto the shower rail (F1) and secure using
140 °F
screw (F4).
100 °F
5.Fit cap (F5).
If there is an offset, wall plate 45 406 special accessory can be ordered.
6.Fit handspray (G) to spray hose (E), see fold-out page V, Fig. [11].
right
left
Attach wall plate (B2).
1.Insert seals (B4) into the wall plate (B2), note position of seal, see detail
view in Fig. [12].
2.Slide wall plate (B2) onto the fitting assembly (C), screw on retaining
rings (B) and tighten using installation tool (B1).
Note: Keep installation tool (B1) for possible future maintenance work
on the shower system.
3.Attach rosettes (B3) to the side sprays.
Operation
Operation of the shut-off handle (H), see Fig. [13]:
Shut-off handle in central position
Shut-off handle clockwise
Press button (H1) and turn
shut-off handle anti-clockwise
Press button (H1) and turn
shut-off handle anti-clockwise fully
Temperature limitation
The safety stop limits the temperature range to 100 °F.
If a higher temperature is desired, the 100 ° limit can be overridden by
pressing the button (J3), see Fig. [14].
Flow control for side shower, see Fig. [15].
= closed
= discharge from hand shower
= discharge from side shower
= discharge from side shower
and hand shower
