Whirlpool AFO ED4 DS Instrucciones Para Uso Y Mantenimiento página 7

EN
4.5E SET UP HUMIDITY
Humidity set point is showed by 10 lightened led .They represent a humidity scale of 11x2 values from
steam cooking (5 bleu led lightened) to dry cooking (5 red led lightened). To set up the chamber's hu-
midity you have to press the key (8) HUMIDITY. It begins to blink, so is possible to select the humidity with
the ENCODER (13) and memorize with the key (12) ENTER.
4.5F SET UP FAN SPEED
With the key (3) FAN SPEED is possible to select the fan speed, if it is enabled by a parameter fixed by the
constructor. You can go to high and low speed by pressing the key (3); the low speed is showed by its
lightened led. When is selected high speed the led of the (3) key is not lightened. It's possible to set up
different fan speeds during the different cooking phases.
4.5G COOKING PHASES
Every cooking cycle, manual or from memorized recipes, may be composed of max 4 phases. The num-
ber of lightened led phases shows the specific phase actually visualized. The selection phase may be
changed by pressing the key (9) PHASES.
You can erase the selection phase by a long pressing of the key (10) CANC. The following phases move
towards left of one position (the yellow lightened led of the phases). It isn't possible to erase all the
phases because a cooking program has to be composed of minimum a phase. You can create a new
phase equal as the selected one; the new phase will be add after the selected one. The following phases of
the selected one move to the right side of one position (the yellow lightened led of the phases). It isn't
possible to create a phase after the 4. If there are four phases and you create a phase after the 4th the
actual fourth will be erased and substituted by the new.
4.5H DELAYED COOKING CYCLE
To set up a delayed cooking cycle, you have to select with the key (13) the temperature under the
minimum value 30°. On visualizer B will appear ''PAU'' ,it means that in this cooking phase the oven will
be in pause for a fixed time that you'll see on visualizer A. At the end of that phase, if there'll be a following
one, the oven will go in this following phase.
4.5L COOLING
When the oven is in STOP status (so with the cycle not started), a fast cooling can be carried out with
opened door. In fact, the message COOL is shown on the flag-shaped display and the ENTER (12) and
CANC (10) keys flash simultaneously when the door is opened. If ENTER is pressed, the cooling option
is confirmed, but with CANC, the oven normal operation is resumed. If the cell temperature is below
60°c, cooling cannot start. Once the COOL option is confirmed, the cooling is started by just pressing
the START/STOP (2) key. Cooling finishes when a temperature of 60°c is reached or when the door is
re-closed. In any case, cooling can be interrupted just by pressing the START/STOP (2) key.
4.5M COOKING PROGRAMS
The oven can memorized max 200 programs (comprehended those pre- memorized by the constructor)
with names of maximum 10 letters. The programs are organized in 2 levels: the first level consists of
7 categories of program: MANUAL-POULTRY-MEAT-FISH-VEGETABLES-CAKES-BREAD-PIZZA-MISCEL-
LANEOUS. The second level defines the particular program (for example: CHICKEN, DUCK, ROAST ...).
Each category (except MANUAL and WASHING) can be made of a great number of programs (the only
limit is 200 max number of total programs). The oven has a set of pre-memorized programs memorize by
the constructor and they can't be modified. They are available translated in 4 languages but there is no
automatic translation for new names memorized by the final user. It's not allowed move or clone
programs from a category to another.
You enter in PROGRAMS mode by short pressure the (11) MENU/MEMO key. The blinking MENU/MEMO
key shows that it is in selection of programs and it's possible to see the programs of the current cat-
egory. On the running display is visualized the program (second level). With (13) and (15) run the
programs and with (12) ENTER key select the program. You can go to a superior level (category of
program) by short pressure of (10) CANC key, MANUAL mode is particular because it hasn't a list of
programs of second level. So when is selected MANUAL mode, by pressing the key (11) MENU/MEMO
passes immediately to program's category selection. for save a new clone program after the reaching
of 100 programs will appear "FULL MEM"; it's possible to over write one of the already present ones or
erase one of the memorized.
7