Idiomas disponibles

Idiomas disponibles

W32LS2 WaLL ManteL and BaSe
Shown with
Carved Corbels
Important: Read entire instruction sheet before
assembling or installing mantel kit.
the W32ls2 mantel is only approved for use with
any DESA Heating Products 32" full size fireplace
system, or firebox and Dimplex electric full size fire-
place. Do not use mantel with any other product.
This mantel kit contains the following:
• Mantel pieces - unassembled and marked as follows:
#1 Base
#2 Right Side with arrow
#3 Right Front Leg with arrow
#4 Left Side with arrow
#5 Left Front Leg with arrow
#6 Header with arrow
#7 Top
#8 Header Assembly Block (2 Pieces)
#11 Carved Corbels
#12 Smooth Corbels
• For use only with Dimplex Electric Fireplace
#8 Dimplex Filler Assembly Block (1 piece)
#9 Dimplex Electric Fireplace Filler Panel
#10 Dimplex Filler Panel Assembly Block (2 Pieces)
• Hardware Kit*
14 - Metal Brackets
28 - Screws M6 x 12 mm (1/2")
26 - Screws M6 x 30 mm (1
26 - Washers M6
1 - Allen Wrench
*Extra hardware may be included.
If any wood pieces are missing or damaged, contact the
dealer where you purchased this mantel for replacement.
If hardware is missing or damaged, contact DESA Heating
Products at 1-866-672-6040 for referral information. You can
also visit DESA Heating Products' technical service web site
at www.desatech.com.
aSSeMBLY and InStaLLatIOn InStRUCtIOnS
118937-01
121149-01
/
")
121335-01
1
4
121336-01
121337-01
www.desatech.com
Note: Gather all mantel pieces together before assembling
mantel.
WARNING: Use only 1/2" screws to attach metal
angle brackets. Damage to mantel will result if other
screws are used for this purpose.
AssemblING mANtel
ImPORtANt: more than one person is required to as-
semble and lift mantel.
Estimated assembly time: 45 minutes.
When assembling mantel do not tighten screws completely
until told to do so. There should be some play in the pieces
to allow for proper alignment and best possible fit. It is very
important that more than one person assemble mantel together.
Panels must be held in proper alignment to each other while
tightening screws to assure fewer gaps and proper surface
alignment. When tightening screws, do not over tighten. This
may cause threads to strip. For this reason, the supplied Al-
len wrench should be used rather than a power screwdriver.
Panels have threaded inserts installed at screw locations.
Screws should start and turn easily in threaded holes when
assembled according to instructions. Do not force screws
into holes.
IMPORTANT: There is a serial number label inside of right
side panel and on outside package. When calling to request
technical assistance or for replacement parts please have
that number ready.
CORbel INstAllAtION
1. Mantel kit contains two sets of corbels, a carved set and
a smooth set. Determine which set you prefer. Discard
other set.
2. From back sides of leg fronts, attach corbels using two
1
/
" screws and washers. See Figure 1, page 2.
1
4
Shown with
Smooth Corbels
Tabla de contenido
loading

Resumen de contenidos para Desa Hearth Products W32LS2

  • Página 5: Base Y Repisa De Chimenea Para Pared W32Ls2

    Nota: reúna todas las piezas de la repisa de chimenea antes ensamblar o instalar el paquete de repisa de chimenea. de ensamblarla. La repisa de chimenea W32LS2 está aprobada sólo para ADVERTENCIA: use sólo tornillos de 1/2" para fijar su uso con cualquier sistema de chimenea de tamaño los soportes metálicos angulares.
  • Página 6 inSTalación dE la ménSula como se indica en la figura 1. Alinee los orificios roscados a los soportes al costado. Pase cuatro tornillos de 1/2" a 1. El paquete de la repisa de chimenea contiene dos con- través de los soportes. Alinee la parte inferior del ensam- juntos de ménsulas, uno esculpido y otro de perfil suave.
  • Página 7 EnSamblE SupEriOr dE la rEpiSa dE chimEnEa Bloque de Panel de relleno ensamble Dimplex (nº 9) Coloque la parte superior de la repisa de chimenea (nº 7) de relleno sobre el ensamble de la misma. Alinee el respaldo de la parte Dimplex (nº...
  • Página 8: Ensamble Del Marco De Adorno (Si Acompañara A La Chimenea A Gas)

    3. Instale la línea de gas. Consulte la sección Conexión EnSamblE dEl marcO dE adOrnO (Si al suministro de gas en el manual del propietario de la acompañara a la chimenea a gas) chimenea. Recuerde dejar acceso para la válvula de 1.

Tabla de contenido