Glacier bay VDR2522A1 Guía De Uso Y Cuidado página 29

Instalación por arriba (continuación)
8
Instalación del dispensador de jabón
Topmount Installation (continued)
Insertar el conjunto del dispensador de jabón (O) a través
8
Installing the soap dispenser
Por debajo del fregadero, atornillar el dispensador de jabón (T)
Insert the soap assembly (O) through the selected hole
al vástago del conjunto del dispensador de jabón (O). Insertar el
in the sink. Secure the soap assembly(O) to the sink with
dispensador de jabón (Q) en el conjunto del dispensador de jabón (O).
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
into the soap assembly (O).
tinued) tinued) continued) continued)
Flushing and checking for leaks
10
9
IMPORTANT: After installation is completed, turn on the
Making the water supply connections
Conexión del suministro de agua
hot and cold water supplies. Check for leaks. Do not lose
the gasket (1) in the hose.
Pull the hose assembly out of the spout and remove
hole hole
NOTE: The hot side inlet tube is indicated by a label. Avoid
the spray head by unscrewing it from the hose in a
NOTA: El conducto lateral de entrada del agua caliente está
nk with nk with
twisting wires together or placing the wires close to each
counterclockwise direction. Be sure to hold the end of
marcado con una etiqueta. Evite enrollar los cables juntos,
other and damaging.
the hose down into the sink and turn the faucet to
colocarlos cerca uno del otro y dañarlos.
the warm position where it mixes hot and cold water.
) onto the ) onto the
Thread the nut (1) on the supply line onto the outlet of the
Q) down Q) down
Enroscar la tuerca (1) de la línea de alimentación en la
Flush the water lines for one minute. This flushes away
water supply valve (2) and tighten with a wrench. Do not
salida de la válvula de suministro de agua (2) y apretarla
any debris that could cause damage to internal parts.
overtighten.
con una llave. No apriete demasiado.
Check for leaks.
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
Q
it back onto the spray hose in a clockwise direction.
O
2
S
T
11
Removing the quick connector
ks
If it is necessary to remove the quick connector (1),
squeeze the tabs (2) on the quick connector and then
pull down to disconnect.
e
d of d of
Topmount
Q
O
S
T
1
1
9
Instalación del fregadero
Aplicar la silicona para sellar (no inc
9
Bajar con cuidado el fregadero (A) en la encimera.
Making the water supply connections
Fijar las presillas de montaje (AA).
Apretar los tornillos de las presillas de montaje por arriba (AA) uniformemente
hasta que el fregadero (A) esté nivelado con la No apriete demasiado.
NOTE: The hot side inlet tube is indicated by a label. Avoid
Con la instalacion de herramienta tornillo.
twisting wires together or placing the wires close to each
other and damaging.
Limpiar el exceso de silicona con un trapo.
Thread the nut (1) on the supply line onto the outlet of the
water supply valve (2) and tighten with a wrench. Do not
overtighten.
1
2
11
Removing the quick connector
If it is necessary to remove the quick connector (1),
squeeze the tabs (2) on the quick connector and then
pull down to disconnect.
Squeeze
1
11
Póngase en contacto con 1-855-HDGLACIER para obtener más asistencia.
2
Pull
down
1
HOMEDEPOT.COM/GLACIERBAY