Stanley HID0109 Manual De Instruccion página 3

HID0109_ManualENSP_011810.qxp 1/18/2010
– The cord should be arranged so that it will not drape over the countertop or tabletop where it can be tripped over, snagged, or pulled on
unintentionally (especially by children).
– The extension cord should be kept dry and off the ground.
WARNING: FIRE HAZARD: Never contact combustible material to the lens and never tape or tie the switch in the on position.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• High intensity discharge bulbs give off heat:
– Do not touch lens while operating.
– Keep combustibles away from spotlight lens. Extreme heat can cause fires.
– Never place the light face-down on any surface when lit.
• Never look directly into the light or shine the light into another person' s eyes.
• Keep sharp objects away from lens — it is glass and can break.
• Do not immerse spotlight in water.
• Do not expose this unit to extremely high temperatures.
• Do not drop or throw spotlight. It contains glass and a sealed lead acid battery.
• Use only with AC or DC charging adapter provided with unit. Plug in the charging adapter at the spotlight first, then plug into the charging source.
• DO NOT OVERCHARGE: Charge up to 8 hours maximum using the AC charging method; up to 7 hours maximum using the DC charging method.
• NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORT SIMULTANEOUSLY.
• After charging/recharging, disconnect the charger and wait 5 minutes before use.
• Do not crush, cut, pull or expose charging adapter cords to extreme heat.
• Position charging adapter cords so they do not become entangled or become a safety hazard. Keep charging adapter cords away from sharp edges.
• Use in a dry location only.
• Do not open body casing. There are no user-serviceable parts inside.
• To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting.
• Do not attempt to charge the unit if the 120 volt AC charger plug is damaged – return the charger to manufacturer for repair or replacement.
SAVE THESE INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new spotlight. Read this Instruction Manual and follow the instructions carefully before using your
new spotlight.
READING THE BATTERY/CHARGE STATUS LED INDICATOR
The battery/charge status LED indicator lights or flashed in three colors to indicate the following:
When charging:
Green (solid): Battery is in a fully charged state.
Orange (flashing): Battery is in a partially charged state (or is charging using the AC charging method).
Red (flashing): Battery needs to be recharged.
When operating:
Green: Battery is operating at full voltage.
Orange: Battery is operating at partial voltage.
Red: Battery is operating at low voltage, and should be recharged.
CHARGING/RECHARGING THE SPOTLIGHT
This unit is shipped in a partially charged state. Charge unit BEFORE FIRST USE using the 120 volt AC charger for 8 hours.
Charge after each use until the battery status LED lights green.
The battery/charge status LED flashes red or orange when the unit is charging using the AC charging method.
Charging/recharging using the 120 volt AC charger
• Make sure the spotlight is off (the trigger lock is in the off position and the trigger is not depressed).
• Insert the barrel connector of the AC charger into the AC-to-DC charging port on the back of the unit. Insert the plug end into a (powered)
standard North American 120 volt 60Hz outlet. The battery status LED flashes red or orange.
• Charge until the battery status LED lights green (approximately 7 to 8 hours).
Charging/recharging using the 12 volt DC charger (optional accessory)
IMPORTANT: The battery/charge status LED does not light or flash when the unit is charging using the DC charging method.
• Make sure the spotlight is off (the trigger lock is in the off position and the trigger is not depressed).
• Plug the double pin tip of the supplied 12 volt DC charger into the 12 volt DC charging port on the bottom of the handle.
• Insert the 12 volt DC plug end into the accessory outlet of your vehicle or other 12 volt DC power source.
• Charge for approximately 5 to 7 hours.
3:03 PM Page 4
4
Note:
When using a vehicle' s 12 volt DC accessory outlet as a charging source, be aware that some vehicles require you to turn on the ignition to power the
accessory outlet.
WARNINGS:
• TO AVOID THE RISK OF PROPERTY DAMAGE, CHARGE UP TO 8 HOURS MAXIMUM USING THE AC CHARGING METHOD; UP TO 7 HOURS MAXIMUM
USING THE DC CHARGING METHOD.
• NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORT SIMULTANEOUSLY.
OPERATING INSTRUCTIONS
Operating the spotlight
IMPORTANT: While most HID spotlights take several minutes to achieve optimal brightness, this spotlight will light brighter for approximately 15
seconds, then dim slightly to the correct brightness level. It was designed this way to function quickly; the slight dimming is not a malfunction.
1. Disconnect from charger.
2. The On/Off trigger is located in the front of the handle of the spotlight.
3. To turn the spotlight on, squeeze the trigger.
4. To turn off the spotlight, release the trigger.
Note: The On/Off trigger can be locked in the on position using the trigger lock switch on the side of the unit.
Operating the LED area lights
The LED area lights located on the top of the unit are controlled by the adjacent LED area light On/Off pushbutton. Refer to the "Features"section
at the beginning of this manual to locate.
Operating the unit corded
Plug the double pin tip of the supplied 12 volt DC charger into the 12 volt DC charging port. Insert the 12 volt DC plug end into the accessory
outlet of your vehicle or other 12 volt DC power source. Operate the unit as outlined in the previous section.
Using the carry lanyard (optional accessory)
The carry lanyard may be used to carry the unit or to hang it for storage. Always adjust the slide on the cords to keep the lanyard secure around
any supporting object.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
• When light is hung by the carry lanyard, do not shake the spotlight or object that it is hanging from. Do not hang the spotlight from any
electrical wires or anything that it is not secure.
• Only use the carry lanyard for hanging this spotlight. The carry lanyard is not intended to support additional weight. Do not attach or hang
anything additional to the spotlight or risk of breakage may occur.
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, we recommend that
the battery is charged at least every 120 days.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the spotlight unit with a soft cloth moistened with a mild
solution of water and detergent.
There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and wires. Contact manufacturer to replace any
components that have become worn or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Contact manufacturer for any information you may need.
SAFE BATTERY DISPOSAL
Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly. Recycling is required,
contact your local authority for information. Failure to comply with local, state and federal regulations can result in fines,
or imprisonment.
To locate a free recycling program collection center near you, go to www.call2recycle.org.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
12 volt DC charger plug fuse replacement
The fuse in the plug end of the 12 volt DC charger protects the adapter' s charging circuit. If the 120 volt AC charger operates, but the DC charging adapter
does not, then this fuse may be opened (blown).
To replace the fuse:
1. Unscrew the end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
5