QSC WideLine-8 Serie Manual Del Usuario página 7

Suspending the WideLine-8 Array
Table 1: WideLine-8 Working Load Limits
Component
EB3082 Extension Bar
AF3082-S Array Frame
AF3082-L Array Frame
PB3082 Pull Back Bar
WL3082 Loudspeaker
WL212-sw Loudspeaker
AF8-10 Adapter Frame
2
M8 Ball Lock Pin
2
M8 Shoulder Screw
2
3/4" Fastener
1- Data available on QSC Audio's website. Please visit http://www.qscaudio.com
2- Working Load Limits are per fastener loaded in double shear. Data is for informational purposes only.
Attaching WL3082 to Array Frame
Before beginning any installation, have your system designer configure the array with proper splay
angles using QSC's EASE Focus (Array Calculator). All orientation of product is to be viewed from the
rear of the enclosure.
1. Attach the array frame to the suspension structure using a 5/8" (16mm) screw pin anchor shackle
and appropriate sling, cable, etc.
2. For arrays of 4 WL3082 or less, pin together the cluster of enclosures or prepare pre-pinned array
from transport cart. Note the QSC logo on the input plate will be right side up when the enclosure is
oriented properly. During assembly, ensure your splay angles are set as desired.
3. Attach the array frame to the top enclosure by inserting the ball-lock pins in the appropriate loca-
tions. Ensure selection of the desired splay angle on the rear link (0°, +5°, -5°).
NOTE: For some array configurations, use of the extension bar and/or pull-back may
be required to achieve the required aiming angle.
When constructing large arrays it is recommended to first assemble units of four
enclosures and then assemble the final array by joining the four enclosure units to
one another.
If extreme uptilt is required, turn the AF3082-L around (rotate 180°) and attach the
WL3082 enclosures toward the rear of the frame; this will allow suspending at a more
extreme upward angle. Note: The markings on the array frame are no longer valid
once the frame is turned around (their positions are reversed).
1
Weight 7:1 Design Factor 10:1 Design Factor
27 lb 1751 lb
(12.3 kg) (714.3 kg)
11 lb 746 lb
(5.0 kg) (339.0 kg)
27 lb 1274 lb
(12.3 kg) (579.2 kg)
3 lb 434 lb
(1.4 kg) (197.4 kg)
38 lb 651 lb
(17.3 kg) (296.1 kg)
109 lb 1274 lb
(49.5 kg) (579.2 kg)
9 lb 326 lb
(4.1 kg) (148.1 kg)
n/a 1810 lb
(822.7 kg)
n/a 1847 lb
(839.4 kg)
n/a 5693 lb
(2587.8 kg)
12:1 Design Factor
1100 lb 917 lb
(500.0 kg) (416.7 kg)
522 lb 435 lb
(237.3 kg) (197.7 kg)
892 lb 743 lb
(405.5 kg) (337.9 kg)
304 lb 253 lb
138.2 kg) (115.2 kg)
456 lb 380 lb
(207.3 kg) (172.7 kg)
892 lb 743 lb
(405.5 kg) (337.9 kg)
228 lb 190 lb
(103.6 kg) (86.4 kg)
1267 lb 1056 lb
(575.9 kg) (479.9 kg)
1293 lb 1077 lb
(587.6 kg) (489.6 kg)
3985 lb 3321 lb
(1811.4 kg) (1509.5 kg)
Figure 10: WL3082 attached to AF3082-S
Figure 11: WL3082 attached to AF3082-L
Figure 12: Detail of WL3082
attached to AF3082-L
Pin rear in center position for 0°
tilt. Upper and lower holes are for
-5° and +5°, respectively.
EN
7