cecotec CONGA 2290 Manual De Instrucciones página 18

ENGLISH
Check the cleaned surface and the time taken.
Check the cleaning history.
Configuration:
Fig. 19.
1. Download the Conga 2000 App from App Store or Play Store.
2. Create an account with your e-mail and password.
3. Confirm login.
4. Add your Conga robot.
5. Connect to Wi-Fi.
Note:
The robot supports 2.4G networks.
The Wi-Fi name and password cannot exceed 32 bits.
If the network configuration fails to connect, follow the below steps:
Press the On/Off button for 5 seconds, the robot will enter sleeping mode and the Wi-Fi light
indicator will blink fast indicating connection error. Retry connecting the robot again following
the steps in the before section.
If the connection fails again, check if:
The robot is too far away from the router.
The Wi-Fi password is incorrect.
* This Conga model is compatible with Alexa and Google Assistant virtual assistants.
Modes
The following modes can be activated from the App:
Auto cleaning mode: From standby mode, press the Auto mode button on the App and the
robot will automatically start operating. It will carry out a cleaning cycle in zigzag motion and
then another one in Edge mode. Once it has finished, it will return to the charging base.
It is the most commonly used cleaning mode and it is used to clean the the whole house's
surface. The robot vacuums the floor's dust automatically, in and organized and efficient way,
as it features memory and gyroscopic navigation supported by its camera.
Moreover, it changes direction when it finds obstacles throughout its route and it returns to
the charging base in a smart and direct way once the cleaning is over. It includes Total Surface
function, through which the robot cleans the whole surface and, if necessary, returns to the
charging base to recharge its battery and finish cleaning.
Edge mode: Select this mode from the App, the robot will clean along the edges and will return
to the charging base through its smart technology once it has finished. If there is no charging
base, the robot will return to the starting point.
Random mode: Select this mode from the App, the robot will start cleaning randomly and then
32
will return to the charging base with its smart technology once it runs out of battery. The robot
will not create any map under this mode.
Twice mode: Select this mode from the App, the robot will carry out 2 whole cleaning cycles.
When the cycle is completed, it will return to the charging base with its smart technology.
Scrubbing mode: Select this mode from the App. When this mode is activated, the robot moves
in a swaying motion, simulating real scrubbing moves. It starts off cleaning in zig zag motion,
then in Edge mode, and finally returns to the charging base taking the straightest way and
memorizing the route. If it runs out of battery before finishing, it will recharge and the resume
cleaning until finished.
Use the App to enter the water intensity mode and select between low, medium or high.
Note:
Do not use the mop outdoors.
Remove the carpets before operating the robot under this mode.
During operation, control the water level on the Wet & dry tank. If it empties, fill it up again
before continuing scrubbing.
Take the Wet & dry tank and the mop out before charging the robot.
Note: In order to ensure perfect scrubbing, moisten the mop before starting scrubbing.
Manual mode: Use the App to move the robot in the desired direction and towards specific
points you wish to clean.
Back home mode: This mode can be activated from the robot, the App or the remote control at
any point of any cleaning cycle. Once it is activated, the robot will automatically return to the
charging base.
Spiral mode: Select this mode for the robot to thoroughly clean a specific spot. It will start
cleaning at a specific point and will move in an outward spiral motion. Then, it will return to the
starting point in an inward spiral motion, and then will go to the charging base.
Smart Area mode: Once the home's map has been saved, select this mode for the robot to clean
an area in zigzag motion. The robot will clean the selected area and then will return directly to
the charging base. The robot will only clean the area selected on the map, therefore it will go
to the point and return to the base without vacuuming.
Spot mode: Select this mode if you want to clean thoroughly a point in the map, making the
most of the robot's maximum power. The robot will clean a specific zone in a spiral motion
and then will return directly to the charging base when cleaning is completed. The robot will
only clean the area selected on the map, therefore it will go to the point and return to the base
ENGLISH
33