Vimar by-me Eikon Guia De Inicio Rapido página 2

Eikon Arké
20529.120 19529.120
Control device with two rocker switches and actuator for SLAVE dimmers
120 V~ 60 Hz, for LED lamps, electronic transformers, RGB LED lamps, RGB
electronic power supplies, to be completed with interchangeable buttons with
1 or 2 modules - 2 modules.
The device cannot control the load directly. It is be used as a double or single button, depen-
ding on the key chosen. The buttons can be configured independently from the SLAVE dimmer
controller and they can be pressed at both the top and bottom.
CHARACTERISTICS.
• Rated supply voltage TP Busbar: 29 V
• Rated supply voltage mains: 120V~, 60 Hz
• Absorption from TP Busbar: 13 mA
• Combinable buttons: double or 1 single
• Terminals: L1, L2, S synchronization, TP busbar
• Possible functions of the buttons:
- ON/OFF switch
- Roller shutters control
- Dimmer control
- Activation of 2 scenarios
• Functions that can be accomplished with the dimmer:
- Switching on, off and dimmering
- Changing absolute colour
- Hue/saturation/brightness adjustment
- FADING-SHOW operation
- "Flash start" mode for CFL lamps
- "Ramp" operation
- Switch-off delay and warning function
- Phase cutting: LE/TE
• Not compatible with By-me control panels with 2 modules and flush-mounted (art.
20510, 16950 and 14510).
• The RGB function is not supported by Article 16969.120.
Controllable loads
SLAVE dimmers
(20137.120-19137.120-16604.120-14137.120-01871.120)
Lamps
(02662.120 o 02663.120)
Adjustable electronic power supplies
(01874.120-01875.120)
Adjustable RGB electronic power supplies
(01876.120)
CONFIGURATION.
FOR THE OPERATIONS OF INSTALLATION AND CONFIGURATION, SEE THE BY-ME
SYSTEM INSTRUCTIONS MANUAL ATTACHED TO THE CONTROL UNIT.
Configuration must be done with the device without the key to be able to press the central
configuration button.
• Functional units: 3 (2 buttons, 1 dimmer actuator), each functional block can belong to at most
4 groups.
• Selection of the functional unit in the configuration phase:
- Press the configuration button and wait for 3s to select the dimmer functional unit;
- Press the configuration button and then the desired button to select
the relevant button functional unit.
The configuration starts when the red LED comes on and ends when it goes out.
When the device is not configured, the actuator is controlled by the left-hand button.
• If the device must be configured as a double button you need to press the left button.
It is recommended to configure the device with the load OFF.
INSTALLATION RULES.
Installation should be carried out in compliance with the current regulations regarding the instal-
lation of electrical systems in the country where the products are installed.
• It should be used in dry, dust-free places at a temperature of between -5°C and +45°C.
• Overloading, power surges and short-circuits may irreparably damage dimmers. Before instal-
lation check the circuit carefully and eliminate any of the above causes.
• The dimmer does not have a mechanical circuit breaker in the main circuit and so is not gal-
vanically separated. The circuit load should be considered always powered.
For further instructions see the manual enclosed with the control panel.
Viale Vicenza, 14 - 36063 Marostica VI Italy
Tel. +39 0424 488 600 - Fax (Export) +39 0424 488 709
www.vimar.com
Idea Plana
16969.120 14529.120
Max no.
20529.120
19529.120 16969.120
14529.120
3
10 Not applicable
10
10 Not applicable
FRONT AND REAR VIEW
Configuration button
LED
CONNECTION WITH UNIVERSAL SLAVE DIMMER
L
N
20529.120
19529.120
16969.120
14529.120
L1 S L2
S
Bus
Maximum length of cables connecting the dimmer actuator and universal SLAVE dimmer: 100 m
MASTER and SLAVE must be configured in the same operating mode.
PAy ATTENTION WHEN CONNECTING THE DIMMER ACTUATOR: terminal L1 to neutral and terminal
3
L2 to phase.
CONNECTION WITH 01874.120-01875.120
10 L
N
20529.120
19529.120
16969.120
14529.120
L1 S L2
S
Bus
CONNECTION WITH 01876.120
L
N
20529.120
19529.120
14529.120
L1 S L2
S
Bus
Maximum length of connection cables between the dimmer actuator and the dimmerable LED lamp or dim-
merable electronic power supplies for LED: 100 m
PAy ATTENTION WHEN CONNECTING THE DIMMER ACTUATOR: terminal L2 to neutral and terminal
L1 to phase.
L1 S L2
L1 S L2
20416 20416
19416 19416
16460
16460
14416 14416
20137.120 20137.120
19137.120 19137.120
16604.120 16604.120
14137.120 14137.120
S S
L
N
S
01874.120 - 01875.120
L
N
S
01876.120
TP Bus terminals
+
-
RGB LED module
RGB LED strip
+
R G B
R
G
B
RGB LED module
RGB LED strip